Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: sfriedberg

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. Well, actually, I often do, especially when I'm...

    Well, actually, I often do, especially when I'm not sure whether I'm giving data for a multinational (like my employer) or not.
  2. You might get a hair more clearance for the...

    You might get a hair more clearance for the holder if you went over to either a TopNotch-style or a vertical triangle style of insert. But in that case, I'd just buy the full profile insert for the...
  3. You definitely need to remove the split cotters...

    You definitely need to remove the split cotters (the clamps for tool shanks) first. Once you get those out of the way, IIRC the bushings are a light press fit.

    You probably need to use a slide...
  4. Generally if you use a partial profile insert,...

    Generally if you use a partial profile insert, you just live with the deeper root. If thread form is critical, buy a full profile insert for the desired pitch.

    If you want to improvise with what...
  5. Replies
    27
    Views
    1,153

    I don't buy in production quantities; it's rare...

    I don't buy in production quantities; it's rare when I buy more than 6 of the same size drill. I usually buy from Travers or KBC Tools, where you can buy anything from cheap no-name to Nachi and...
  6. Replies
    22
    Views
    15,784

    Bart, a typical rule of thumb is one hour soak...

    Bart, a typical rule of thumb is one hour soak per inch of thickness. So 1/16" thin plates should not require much soak time. In fact, I'd probably be worried more about confirming they actually...
  7. Not-even-that-old-school technique: Holding...

    Not-even-that-old-school technique: Holding 14x18" in a vise? Forget that. Use strap clamps and clamp it to the table (or precise blocks placed under the strap clamp contacts). If you need to...
  8. Replies
    2
    Views
    240

    As far as I know, there is only one version of...

    As far as I know, there is only one version of the Hardinge 4 degree taper spindle nose. So any Hardinge chuck, faceplate, or step collet closer with the 4 degree taper will fit your machine. ...
  9. Before you can bore a taper, you have to drill it...

    Before you can bore a taper, you have to drill it out to make room for the boring bar. Jobber length drills aren't long enough for the job. Taper length drills are long enough for typical shallow...
  10. Glad you got it sorted, I am sure the hours spent...

    Glad you got it sorted, I am sure the hours spent messing with it were frustrating. Even gladder you mentioned the problem here, as a reminder/tip.
  11. I bet he has a real familar name, too.

    I bet he has a real familar name, too.
  12. B&S #00 screw machine used 5/8" shanks, B&S #0...

    B&S #00 screw machine used 5/8" shanks, B&S #0 screw machine used 3/4" shanks, B&S #2 screw machine used 1" shanks.
  13. Replies
    10
    Views
    916

    Turbowerks, when you say "billet", do you mean...

    Turbowerks, when you say "billet", do you mean "blank"? 'cause a billet is a massive semi-rough piece from a smelting foundry that goes to a forge or a rolling mill for further processing. Just...
  14. They aren't labeled with an industry-standard...

    They aren't labeled with an industry-standard code, and the square arbor hole is certainly not common. So these were probably house-branded "proprietary" wheels for some specific make and model of...
  15. Replies
    45
    Views
    3,710

    eKretz, in that fourth photo, is the "shadowed...

    eKretz, in that fourth photo, is the "shadowed overhang" an artifact of the contrast enhancement?
  16. Replies
    11
    Views
    828

    Combine a hinge/pin with an additional stop+clamp...

    Combine a hinge/pin with an additional stop+clamp bolt, through both parts a few inches from the hinge, to fix the angle where you want it.

    Or just make a small solid taper block (small enough not...
  17. Replies
    12
    Views
    1,802

    Stroke? (Hard to tell that from photos with no...

    Stroke? (Hard to tell that from photos with no size reference.)
  18. Replies
    31
    Views
    2,045

    Do you know the material (A500, A513, 1026,...

    Do you know the material (A500, A513, 1026, 12L14)? Easy machining alloys are (roughly) exclusive of easy welding.

    But it's more likely the surface of the material is contaminated. "Buffing...
  19. Did Columbia Steel Casting in Portland ever...

    Did Columbia Steel Casting in Portland ever commit to host another class? I'd be interested in either Seattle area or Portland, but have some schedule commitments before and after Thanksgiving.
  20. Replies
    14
    Views
    1,727

    That seems like an excellent price. Even a (new)...

    That seems like an excellent price. Even a (new) Chinese import 16x40 is going to cost three times that.
  21. Replies
    23
    Views
    1,632

    I'm very envious. That's a very good condition...

    I'm very envious. That's a very good condition machine.

    If I ever clean out about 25% of the floor space in my shop, a 6" slotter would be one of the things I'd look for to fill the space back up...
  22. Yes! This level of detail is very helpful and...

    Yes! This level of detail is very helpful and encouraging to other owners of leaky VNs.
  23. I miss Enco. Not everything they carried was...

    I miss Enco. Not everything they carried was that good, but they had some excellent deals. I used to buy most of my shop consumables from them.
  24. See if one of your local riggers will store the...

    See if one of your local riggers will store the machines for you. Some have no facilities for it, others do. You might get a decent price (compared to self-storage plus two separate rigging jobs)...
  25. Bore an internally threaded 5C emergency collet...

    Bore an internally threaded 5C emergency collet out to 1". The only way that won't work is if your part requires more than about 1.5" of contact depth (incredibly unlikely), or if the part will...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4