Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Peter from Holland

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    15
    Views
    882

    I worked in some brick works and we chisseled off...

    I worked in some brick works and we chisseled off bolt regulary
    Faster as a blow torch If you could reach it with the chissel at least
    If we could get in the right position we smashed the bolt...
  2. Replies
    2
    Views
    166

    Hello Ed Welcome to the forum On the treading...

    Hello Ed
    Welcome to the forum
    On the treading chart it says the machine is able to thread "Whitworth" which is in fact TPI
    You even do not need to change the change gears for switching from...
  3. If you use a spring preload on the bearing bigger...

    If you use a spring preload on the bearing bigger as the actual load you end up with zero clearance And as the speed is this low it could be done probbably
    You can do it by making a plain bearing...
  4. Awire gear Module 2 with 12 teeth will fitt...

    Awire gear Module 2 with 12 teeth will fitt probably

    Peter
  5. Those blanks are hobbed If it is a standard M2...

    Those blanks are hobbed If it is a standard M2 rack the 12 teeth gear will fittAlso it is a horizontal adjustment Weight is not a issue Peter
  6. Replies
    6
    Views
    901

    Ucimu is a italian producers association ...

    Ucimu is a italian producers association
    Quality machines mainly

    Peter
  7. Oke Now I see Not much torc then and no chance...

    Oke Now I see
    Not much torc then and no chance in a catastrofic failure
    Buy the gears then and connect these to a shaft

    Peter
  8. If I would decide to go this route I would buy 2...

    If I would decide to go this route I would buy 2 of those gears and mount them back to back to get the hight of gear you need Problem I see is howto connect the gears to the shaft strong enough to...
  9. I found a picture of a PA20dgr M2 Z12 gear I...

    I found a picture of a PA20dgr M2 Z12 gear
    I see no undercut 332518


    But then gear needed by the OP can be a stub gear also
    With gears one can do so many different things So you never know...
  10. The system of cutting with a single profile gear...

    The system of cutting with a single profile gear cutter in a disk form will not allow any undercut Physically impossible
    Simple

    The specs say what they say So probably the undercut is not...
  11. You cannot undercut when using a dividing head...

    You cannot undercut when using a dividing head and a single profile gear cutter
    You automaticly do it with a generating proces Yes But not with a gear cutter and dividing head Impossible through...
  12. Replies
    6
    Views
    625

    Hard to get on this side of the pond Best...

    Hard to get on this side of the pond
    Best chance is the UK perhaps
    I found this one pretty quick
    Mild Steel Square Tube S235/S275 | Metal Supermarkets UK
  13. To eliminate undercut you can make the pressure...

    To eliminate undercut you can make the pressure angle bigger
    One of the reassons industrie went from 15 dgr to 20 dgr To be able to make smaller gears
    If you ever opened up a electric handdrill...
  14. You did your calculation perfectly In spite of...

    You did your calculation perfectly In spite of all the nonsence comments on going DP first and then convert
    12 Teeth Mod 2 will give you a OD of the gear of (12+2)x2=28mm
    So order the Mod 2...
  15. To determen the modul of the gear devide the...

    To determen the modul of the gear devide the pitch of the rack in mm by 3.14
    That is usefull information when ordering the tool
    A usefull formula is OD of the gear in mm = Modul× (Z+2)
    Z=number...
  16. Replies
    30
    Views
    2,461

    Indeed And then a 5axes machine The software...

    Indeed And then a 5axes machine The software from klingelnberg and go at it
    peter
  17. Replies
    30
    Views
    2,461

    On automotive gears it is not unusual to have...

    On automotive gears it is not unusual to have specific pressure anglesIts not like you buy a 20dgr hob and machine away If you do not have the specifics of the gear you always have to make at least a...
  18. MAny variables YOu came up with the idea So let...

    MAny variables
    YOu came up with the idea So let us knowhow it works out

    Peter
  19. Thats a drill press not a milling machine Not...

    Thats a drill press not a milling machine Not gonna work if you cannot push or pull the morsetaper in its cone
    You cannot tighten the collet and with a ER colletsystem the sideloads will get it...
  20. Replies
    30
    Views
    2,461

    I hope you have a manual for it A Mikron 102.5...

    I hope you have a manual for it
    A Mikron 102.5 needs a differential to cut helical gears
    That differential is in a housing behind the left door And you have 2 different housings which can be...
  21. Replies
    11
    Views
    1,506

    If you have no experience in machining every...

    If you have no experience in machining every machine that can cut metal looks impressive
    So a hobbyist telling me any of those cheap machines(Made in China or anywhere else) are good I would not...
  22. Replies
    2
    Views
    809

    Drive dog is easy to make yourself As you seem...

    Drive dog is easy to make yourself
    As you seem to use the Din 2080 tooling or US equivalent you need a 1mm shim with 2 notches on the inside and then 2 drive dogs also with a notch each
    Looks...
  23. All depends on what load the pivot point sees and...

    All depends on what load the pivot point sees and dimensions
    You gave us no indication so far

    peter
  24. Replies
    6
    Views
    501

    I could not find it for the TNC111 eighter ...

    I could not find it for the TNC111 eighter
    Here is a link to the simular TNC113 service manual https://product.heidenhain.de/JPBC/image/HWP.DE/hlr-system/599239-00-a-02.pdf
    Perhaps it helps
    ...
  25. Replies
    6
    Views
    501

    On the dokumentpage on heidenhain.de or com you...

    On the dokumentpage on heidenhain.de or com you find the usersmanual and more I only have my phone at hand now and that makes searchi g harder as at the laptop or computer

    Peter
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4