Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: coyoinu

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    12
    Views
    881

    if X+ is coming toward you, and Z+ goes to the...

    if X+ is coming toward you, and Z+ goes to the right, Y+ points straight down, according to the right hand rule.

    if you're doing any work in G19 plane, that one has G2 and G3 reversified from the...
  2. Replies
    46
    Views
    4,984

    So the machine does powerup fine with B working...

    So the machine does powerup fine with B working as expected, but borks out while running the program? Does B respond to hand jogging?

    Ya, sounds to me like a brake problem. It could be as...
  3. Replies
    2
    Views
    982

    if you're circle interpolating bores on a Haas,...

    if you're circle interpolating bores on a Haas, you need to be around 40 IPM or less to get "round" holes.
  4. Replies
    6
    Views
    950

    Adding to this, selecting the appropriate tip...

    Adding to this, selecting the appropriate tip direction will also be important to creating the feature correctly
  5. straight from the factory the tables can be out...

    straight from the factory the tables can be out of flat by .0015

    if you're using a tenths indicator, simply leaning on the sheet metal too hard is enough to distort the reading.
  6. Replies
    4
    Views
    1,470

    Coldfire alarm text says "Electronics fault. No...

    Coldfire alarm text says "Electronics fault. No communication between processor and Mocon. Power failure can be verified if Status LED on Mocon blinks four times at power up. Test +12 / -12 VDC to...
  7. Replies
    11
    Views
    2,245

    i don't think the gauge pin will be adequate. ...

    i don't think the gauge pin will be adequate. how do you know the length of the assembly? did you check the runout?

    there should be a master calibration tool which will have a known gauge...
  8. yeah the MRZP calibration has to be dead nuts,...

    yeah the MRZP calibration has to be dead nuts, probe included.

    markp posted a long-hand method to make the calibration, albeit for a different machine type
    ...
  9. Replies
    11
    Views
    2,245

    it sounds like you're starting the routine with...

    it sounds like you're starting the routine with no tool length offset for the probe. I find best results are had with "COMPLETE PROBE CALIBRATION", using both the calibrated gauge tool and the...
  10. remote share like netshare? Networking -...

    remote share like netshare?

    Networking - Troubleshooting Guide - NGC

    i've found that a netshare folder w/ more than 500 files in it causes problems with display and refresh speed.
  11. Replies
    18
    Views
    3,822

    maybe you can fill it with silicon bronze...

    maybe you can fill it with silicon bronze brazing, machine it back down, and finish flat.
  12. Replies
    2
    Views
    422

    well, the newest machines keep the door locked...

    well, the newest machines keep the door locked until the spindle is under 100 rpm, but there's a couple of things that the control simply can't protect you from (like if the encoder takes a hike)
    ...
  13. Replies
    2
    Views
    1,813

    post your code

    post your code
  14. Replies
    2
    Views
    377

    Settings -> User Positions -> Tailstock

    Settings -> User Positions -> Tailstock
  15. ^hey M, nice super mini mill 2 you got there

    ^hey M, nice super mini mill 2 you got there
  16. if grease-type lube, make sure that all lines are...

    if grease-type lube, make sure that all lines are functioning and flowing (rather than full of wax)
    good backup of parameters?
  17. Replies
    6
    Views
    1,374

    is this a UMC? if so, try this test again,...

    is this a UMC?

    if so, try this test again, and open the door gently but with enough force to bump the stops. watch the indicator while you do that.
  18. Thread: Haas simulator

    by coyoinu
    Replies
    5
    Views
    870

    offsets, bro

    offsets, bro
  19. Replies
    48
    Views
    5,492

    Poll: get a bridgeport, or a even better, a tree. i...

    get a bridgeport, or a even better, a tree.

    i saw a guy w/ a masters degree in mechanical engineering running the tree once. As he was lowering the saddle we start hearing CRUNCH CRUNCH CRUNCH. ...
  20. SHIFT-Recover should do the trick.

    SHIFT-Recover should do the trick.
  21. seen 'em sitting there, not so much in action. ...

    seen 'em sitting there, not so much in action. high speed hsk seems nice if that's your thing. the relatively small head on such a big footprint of a machine makes it look like that dude in the...
  22. Replies
    40
    Views
    4,029

    good luck on the move to save some trouble,...

    good luck on the move

    to save some trouble, you could always leave one of the monarchs with me in Burbank ;-)
  23. ya that's unfortunate. the manual says a...

    ya that's unfortunate.

    the manual says a draw-back collet is needed to ensure correct barfeed behavior. it's possible the bar can catch the back side of a jaw depending on orientation.

    as...
  24. odd question, does this program use G112...

    odd question, does this program use G112 anywhere?

    Also, what's with the little stub in the pictures? it kinda looks like the end of a bar rather than the start of a new one.
  25. Replies
    13
    Views
    1,756

    20500 rpm, thanks for the tip, Mr. Safety.

    20500 rpm, thanks for the tip, Mr. Safety.
Results 1 to 25 of 199
Page 1 of 8 1 2 3 4