Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Gearbreaker

Search: Search took 0.00 seconds.

  1. Got it apart.... finally, needed a little heat...

    Got it apart.... finally, needed a little heat and then cooling to loosen it enough for my puller to get it to budge.
  2. Got it and got it apart finally. Thank you!

    Got it and got it apart finally. Thank you!
  3. HGR is great when visiting. I bought something...

    HGR is great when visiting. I bought something on Ebay that they were selling and traveled to pick it up. They gave me the run of the place. I found some small items and asked about a price for...
  4. Heavy 10 drawbar disassembly procedure.

    I am trying to remove the tube from my heavy 10 5C drawbar. The manual shows two pins need to be removed. However, they are/were in what look(ed) like blind holes. The bearing assembly has holes but...
  5. Thank you. I'm rather new here. I didn't...

    Thank you. I'm rather new here. I didn't realize that there was a SB area. Perhaps I can move it myself by copying it there and then deleting it. Here goes....
  6. South Bend drawbar disassembly problem....

    [ATTACH=CONFIG]271725
    I am trying to remove the tube from my heavy 10 5C drawbar. The manual shows two pins need to be removed. However, they are/were in what look(ed) like blind holes. The...
  7. South Bend drawbar disassembly problem....

    [ATTACH=CONFIG]271725
    I am trying to remove the tube from my heavy 10 5C drawbar. The manual shows two pins need to be removed. However, they are/were in what look(ed) like blind holes. The...
  8. Replies
    21
    Views
    1,660

    Thank you all for your input. It was very...

    Thank you all for your input. It was very helpful. I ended up purchasing a $12 B16 1/2" drill chuck and fitted it onto the shaft with no modifications. It locked right on and has a runout (3" out...
  9. Replies
    21
    Views
    1,660

    I agree that making an adapter would be best but...

    I agree that making an adapter would be best but I am not that skilled with my lathe yet. I understand that tapers can be tricky. However, perhaps modifying the existing machines taper to a standard...
  10. Replies
    21
    Views
    1,660

    That B16 sure looks promising. If I am figuring...

    That B16 sure looks promising. If I am figuring right, by the time you do the math the difference front to back is only.03". I am under the impression that the B tapers are metric based and the...
  11. Replies
    21
    Views
    1,660

    I'd bet this is supposed to be the same setup but...

    I'd bet this is supposed to be the same setup but I got no adapters with the machine. I figure with a collet adapter I can fit the coil forms onto a simple custom machined holder locked in a collet....
  12. Replies
    21
    Views
    1,660

    Checked dimensions and they are pretty accurate.

    Checked dimensions and they are pretty accurate.
  13. Replies
    21
    Views
    1,660

    I don't think it is necessary to use the entire...

    I don't think it is necessary to use the entire shaft so that may be the key. The shaft is one piece all of the way through so it is a part custom made by the company for the application. The nut...
  14. Replies
    21
    Views
    1,660

    I measured with a caliper. I'll double check...

    I measured with a caliper. I'll double check them and let you know but I believe the measurements to be pretty close.
  15. Replies
    21
    Views
    1,660

    270269Here is the pic. Hopefully it comes...

    270269Here is the pic. Hopefully it comes through. It is the lower shaft with the cap screw sticking out of it.
  16. Replies
    21
    Views
    1,660

    Thank you. I am currently on an android so the...

    Thank you. I am currently on an android so the icon isn't here. I will post a pic as soon as I can get to a PC.
  17. Replies
    21
    Views
    1,660

    I don't see a provision for uploading pics. How...

    I don't see a provision for uploading pics. How can I do this?
  18. Replies
    21
    Views
    1,660

    I would certainly supply the machine information...

    I would certainly supply the machine information but unfortunately it has no markings.
  19. Replies
    21
    Views
    1,660

    What is this weird tapered shaft?

    I have aquired a coil winding machine on which there is a tapered shaft. I need to buy an adapter to change it to an ER collet holder but I cannot figure out the taper type. It is 1.2" long, the...
Results 1 to 19 of 19