Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: bridgedog

Page 1 of 26 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    33
    Views
    2,855

    Turn off the gas and now you have a gasless mig....

    Turn off the gas and now you have a gasless mig. I run both wire through mine. Once you learn a little you will be glad you bought a gas type mig. You can't go the other way.
  2. Replies
    25
    Views
    2,245

    So you sold a vice for the amount you asked and...

    So you sold a vice for the amount you asked and now you want to get more? :icon_bs:
  3. It must be billet.:stirthepot:

    It must be billet.:stirthepot:
  4. Replies
    10
    Views
    773

    Looks to be following photo bucket business plan....

    Looks to be following photo bucket business plan. Wait until every one loads up then charge more.
  5. Replies
    51
    Views
    2,649

    Interesting. My post just disappeared. I had to...

    Interesting. My post just disappeared. I had to go to activity stream to find it
  6. Replies
    51
    Views
    2,649

    I have been getting the same thing but not all...

    I have been getting the same thing but not all the time. I thought it was related to me rebooting my computer.
    P.S. Hey Ray I used my bandsaw clamp yesterday and it always makes me think of you. :D
  7. You might look into the injector cups as this is...

    You might look into the injector cups as this is a common place to loose coolant. I replaced mine at 285 k miles when I did the injectors. Two of them were showing signs of leaking.
  8. Replies
    33
    Views
    4,280

    watch out for the little slivers of material. Not...

    watch out for the little slivers of material. Not only are they hot they also can get into the motor and make many
    sparks and smoke! I found this out the hard but very exciting way.:D
  9. Replies
    49
    Views
    5,714

    Ipads are a little harder to wipe with !

    Ipads are a little harder to wipe with !
  10. Replies
    13
    Views
    1,476

    valve lifter and adjustment cover. Remove and...

    valve lifter and adjustment cover. Remove and weld or goober it up again. Cork gasket will work best. Good time to check valve adjustment as they sometimes get tight and will float a valve. There may...
  11. Replies
    7
    Views
    1,095

    Was it brand new when reconditioned? If not I...

    Was it brand new when reconditioned? If not I don't see it happening.
  12. Replies
    18
    Views
    2,860

    I have had a few dips like that on my road...

    I have had a few dips like that on my road through life. Well maybe more than a few.
  13. Replies
    32
    Views
    2,248

    I do hope you made some reference marks when...

    I do hope you made some reference marks when taking it apart. I have witnessed many vibrating shafts that were not assembled in the same line as original. I hate the small vibrations so much I had it...
  14. Replies
    19
    Views
    2,803

    V twin? It has been about fifty years since I...

    V twin? It has been about fifty years since I worked for H.D. I am probably stating the obvious but make sure you lap the rods as a pair.
  15. That is for silk screening polka dots on bikinis.

    That is for silk screening polka dots on bikinis.
  16. Replies
    38
    Views
    37,203

    Yea that paper is seven years older now

    Yea that paper is seven years older now
  17. I have to agree in this application a small hole...

    I have to agree in this application a small hole 90 degrees of the side is the best and most durable. I have seen those
    pesky little bugs that build a mud nest in any hole they can find create...
  18. I have been known to use an old ford fuel filter...

    I have been known to use an old ford fuel filter for a vent with built in filter. The ones that screwed into the carb
    had pipe thread. Yea I know sometimes I am a hack ;)
  19. Vents are funny things. Years ago working at a...

    Vents are funny things. Years ago working at a H.D. shop we had a new sportster go out the door only to break down within 2 miles. No cell phones in the 60's so the customer got to a phone and called...
  20. Just a little side note. I have had gearboxes...

    Just a little side note. I have had gearboxes that had a plugged vent. It gets hot and pushes oil out and sucks in cold air when it cools.
    Seals were replaced on one twice before we figured it out.
  21. Replies
    24
    Views
    2,667

    That would be a Poo-lazzy I believe.

    That would be a Poo-lazzy I believe.
  22. Replies
    24
    Views
    2,667

    12 posts and no politics. I am starting to like...

    12 posts and no politics. I am starting to like this thread.
  23. Replies
    30
    Views
    2,662

    times two on the trebuchet. Way cool ancient...

    times two on the trebuchet. Way cool ancient technology.
  24. Been there done that only we made bearing...

    Been there done that only we made bearing replacement slugs with a precision hole through them. Run a piece of polished and ground shaft through the whole mess to keep the bearing alignment. Makes it...
  25. Replies
    75
    Views
    6,819

    I am having a hard time deciding if someone is...

    I am having a hard time deciding if someone is off their meds or on some meds!
Results 1 to 25 of 647
Page 1 of 26 1 2 3 4