Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Richard King

Page 1 of 60 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    77
    Views
    4,763

    I see your step grinding!! Good Job!

    I see your step grinding!! Good Job!
  2. Replies
    77
    Views
    4,763

    GOOD JOB!!! Yeah I was at Cloyes Gear doing the...

    GOOD JOB!!! Yeah I was at Cloyes Gear doing the slant bed lathe. They bought the good expensive ones. I am so impressed with your work, wanting to learn and teach. THANK YOU!!
  3. Spray the black side to clean too as your fingers...

    Spray the black side to clean too as your fingers have oil on them.... I would wear some nylon gloves. If you look at Ians thread about his Fadal...he uses the epoxy..he put the glue on a bit thick...
  4. Yes....when you look at the material...one side...

    Yes....when you look at the material...one side is a bright smooth aqua colored side.... the opposite side is a dark, almost black, that side is acid etched and that is the side you bond. Be careful...
  5. aaron, Didn't we discuss about this a few years...

    aaron, Didn't we discuss about this a few years ago? I recall talking to a Canadian guy for an hour about replacing the Turcite. Also talked about coming up to help, but I never did...was that you?
  6. The BURBANK CA class is full. Thanks

    The BURBANK CA class is full. Thanks
  7. Replies
    77
    Views
    4,763

    I used dozens of the snap in disks, when it got...

    I used dozens of the snap in disks, when it got dull I switched it. ...
  8. Replies
    815
    Views
    25,795

    Biden will end the ban on Muslims coming here...

    Biden will end the ban on Muslims coming here from Iran. Do you think there is a chance a few maybe terrorist? He made this commercial to play with Arabic captions to Muslims like Rep Omar that...
  9. Replies
    77
    Views
    4,763

    Sure.... I saw you called, but I was driving in...

    Sure.... I saw you called, but I was driving in a snow storm. We got 8" of snow today.... Another way of looking at it is to paint the high area with Dykem fast dry lay out fluid and grind off...
  10. My Friend and student Chris Colbert (ME) will...

    My Friend and student Chris Colbert (ME) will start to produce Lighter then Light Straight-Edges. When he has some I will let you know.
  11. There is also a great grinding company /rebuilder...

    There is also a great grinding company /rebuilder in TN Schmiede Corporation | Way Grinding
  12. Replies
    77
    Views
    4,763

    Lanagos, You need to "blind" grind the way,...

    Lanagos,

    You need to "blind" grind the way, not do the "square cut" method your doing. Take all of the area until you are say with in .0005" and then do what your doing. Blind scraping is when...
  13. Replies
    77
    Views
    4,763

    Ian, How's it going? Most of us are curious...

    Ian,

    How's it going? Most of us are curious how it is going and I like how your going about it for the most part. It is obvious you have been reading this forum for years and watching You Tube...
  14. I've been installing spindle bearings for 45+...

    I've been installing spindle bearings for 45+ years. I have never heated bearings to 400 F. I was taught to never heat them over 250 F. I have a cone shape bearing heater and I used to use a wax...
  15. Make sure you have the bearings facing the right...

    Make sure you have the bearings facing the right direction. http://vintagemachinery.org/pubs/2682/4155.pdf

    I found this one on Vintage machinery and it looks like they are back to back...or fat...
  16. Replies
    77
    Views
    4,763

    This what I used:...

    This what I used:...
  17. Replies
    77
    Views
    4,763

    Some folks can't afford to send it to a Surface...

    Some folks can't afford to send it to a Surface Grinding company. I think he is doing a super job and this thread should be a sticky on top as it shows a regular machinist can rebuild a machine...
  18. Replies
    77
    Views
    4,763

    I'd do both...but take a little at a time. I...

    I'd do both...but take a little at a time. I would not use the rough disk you showed in the first few posts. Start out slow and work your way into it. So far so good, your doing fine. Flip the...
  19. Replies
    5
    Views
    407

    You should ask this question in the Woodworking...

    You should ask this question in the Woodworking forum
  20. Those questions can be answered by Richard...

    Those questions can be answered by

    Richard Cedrone [email protected] - the president of

    Bearing Manufacturer | Bearing Supplier | TriStar Plastics The also have Q&A section on their...
  21. I got an email back from my friend Lance, I was...

    I got an email back from my friend Lance, I was wrong of the state, sorry:

    "The folks I used were in South Carolina. Here is their contact info:
    I dealt directly with Jody!"


    Machinery...
  22. Replies
    77
    Views
    4,763

    It would seem to me It depends on what your going...

    It would seem to me It depends on what your going to be using the machine for? Ideally you would have had the ways ground on a way grinder, but you could have done it by hands and it would work. I...
  23. All Bridgeport's of old had that low spot. I...

    All Bridgeport's of old had that low spot. I think the did that so when they machined the back of the knee it sat on 4 outside sections and no chance it was high in the middle. I'll email him now...
  24. Replies
    77
    Views
    4,763

    It is tough not being there and trying to give...

    It is tough not being there and trying to give advice. The step looks like it was a factory design or a FK-Up, what do the new factory guys think about it? If you want to grind off the ridge, go...
  25. Have a depth mike? Mike down from the clearance...

    Have a depth mike? Mike down from the clearance surface above the dovetail. It is no doubt worn in the center and high on the ends. If you want to make it better you will have scrape it . I...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4