Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: gbent

Page 1 of 60 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    6
    Views
    780

    Aejgx6, are you still interested?

    Aejgx6, are you still interested?
  2. Replies
    7
    Views
    497

    3:1 is not an adequate safety factor in a dynamic...

    3:1 is not an adequate safety factor in a dynamic environment such as your sailboat.
  3. Replies
    19
    Views
    1,273

    I'm going to disagree with that. I have an older...

    I'm going to disagree with that. I have an older 3000 psi shop, and a newer with a 5000 psi floor. The durability of the 5000# floor is much better. Smaller impacts that would spall the weaker...
  4. Replies
    6
    Views
    479

    Don't smoke. You will get about a 50% derate,...

    Don't smoke.

    You will get about a 50% derate, but they are available.
  5. If it was I, the depth of cut would be 3 or 4...

    If it was I, the depth of cut would be 3 or 4 passes to get the 5/16 depth of cut. Then with each successive pass I'd back the table return dog by another 1/2".
  6. Replies
    6
    Views
    479

    Are they 480v? Are they single phase capable? ...

    Are they 480v? Are they single phase capable? Do you have manuals or installation documents?
  7. Replies
    0
    Views
    287

    WTB D1-6 back plate

    I need a D1-6 back plate for a 15" Buck Chuck. The factory is 11 3/4 in diameter, but I could sleeve if undersize.

    edit: Needs to be a 6 pin.
  8. Replies
    19
    Views
    1,273

    Good concrete starts with proper subgrade...

    Good concrete starts with proper subgrade preparation. While I'm sure it exists somewhere, I have never seen asphalt have proper subgrade prep for concrete. In fact, zero subgrade prep seems to be...
  9. Replies
    19
    Views
    821

    The last vaporizor I bought for a forklift was a...

    The last vaporizor I bought for a forklift was a replacement part with an adjustment specifically for worn, low vacuum engines.

    Ox, lets see a picture of the vaporizor as well.
  10. Replies
    19
    Views
    821

    After the rebuild have you adjusted the...

    After the rebuild have you adjusted the carburetor? my thought is you have much more engine vacuum now so it is pulling a little more propane out of the vaporizer.
  11. Replies
    8
    Views
    516

    The straight knurl means they meant for you to...

    The straight knurl means they meant for you to use a pipe wrench.
  12. Replies
    19
    Views
    1,095

    I, too, have heard the stories. But I have also...

    I, too, have heard the stories. But I have also seen photos I think were authentic from the late 1800's/early 1900's showing early settlers with 6+ foot long catfish.
  13. Thread: Use of Dry Ice

    by gbent
    Replies
    21
    Views
    1,556

    The dry ice and alcohol is used for freeze...

    The dry ice and alcohol is used for freeze branding animals. Gasoline works as well.

    For those of you who are used to fishing parts out of liquid nitrogen need to heed this advice: never try...
  14. Replies
    32
    Views
    2,416

    There is also a welding technique called lay...

    There is also a welding technique called lay wire. Basically, you just lay the wire on top of the joint while welding. The amount of reinforcement for the joint can be controlled by selection of...
  15. I'm not even sure he is a renter. It sold at a...

    I'm not even sure he is a renter. It sold at a Sheriff's sale. That is state law area, but often that convey's immediate possession, and there are few to no allowable legacy contracts or...
  16. Replies
    6
    Views
    716

    You might try a welding forum. The big Lincoln...

    You might try a welding forum. The big Lincoln gas SA machines used that engine.
  17. Replies
    6
    Views
    780

    The tube is a CTL (now owned by L3) F6400. ...

    The tube is a CTL (now owned by L3) F6400. Another label suggests there are additional characters unreadable, and ending in "N". It is a 450 KHZ machine.
  18. Replies
    11
    Views
    879

    Half scrap price? I'd have owned it too, and...

    Half scrap price? I'd have owned it too, and I've already got one.
  19. ebay has lots of Tantung, and sometimes different...

    ebay has lots of Tantung, and sometimes different brands. You got hosed.
  20. Replies
    6
    Views
    780

    FS 5 kw Taylor Winfield induction heater

    I bought it for a tig torch cooler and to play with the electronics. I found a proper tig torch cooler. I looked at the electronics and thought I might learn some lessons, Darwin style. It was...
  21. Replies
    3
    Views
    525

    SEattle Boeing Airplane Company

    SEattle Boeing Airplane Company
  22. Replies
    12
    Views
    795

    Your pilot hole needs to be smaller in diameter...

    Your pilot hole needs to be smaller in diameter than the web on your 5/8 drill. With an oversized pilot hole the drill wants to vibrate and will loosen your taper.
  23. Replies
    11
    Views
    879

    On smaller plates the holes are for lifting lugs....

    On smaller plates the holes are for lifting lugs. Using a spreader bar the plate can easily be turned upside down to make a scraping print. I imagine your plate would be used the same way.

    How...
  24. Replies
    7
    Views
    651

    PM inbound

    PM inbound
  25. My guess is something significant diameter and...

    My guess is something significant diameter and length was held in the chuck. The miscreant then did heavy work without the support of the tailstock. Or even more likely, tried to part a workpiece...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4