Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: chad883

Page 1 of 7 1 2 3 4

Search: Search took 0.00 seconds.

  1. Mazak lathes will call the last known offset for...

    Mazak lathes will call the last known offset for that tool, if that tool has not been called yet it will default to the primary offset. Call T0101 will bring up tool 1 offset 1. Call T0101.2 it will...
  2. Replies
    18
    Views
    813

    Make sure you have your radius set correctly in...

    Make sure you have your radius set correctly in tool offset. Half the end mill diameter.
  3. Replies
    10
    Views
    773

    I thought end mills are always set to "0"...

    I thought end mills are always set to "0" setting. I always have them set for that, but do not program in degrees. I use polar milling.
  4. If you are storing the program in the machine...

    If you are storing the program in the machine memory, 1 device moved from machine to machine. The ones in the link are for that purpose, they have ones that stay at the machine also. I think that is...
  5. Easiest thing I have ever used. DNC,...

    Easiest thing I have ever used.

    DNC, xlTRANSFER

    or

    Portable USB Connect from Shop Floor Automations

    I have used the first one on my 1995 Fanuc controlled Mori, and it is fine. I have used...
  6. Replies
    26
    Views
    2,644

    The biggest concern would be what control voltage...

    The biggest concern would be what control voltage your control needs. A lot of CNC machines need 24V DC. If your supply power is too high or too low, it will either burn up your boards/drives, or not...
  7. Replies
    1
    Views
    476

    Sounds like your hard drive went out. Timing...

    Sounds like your hard drive went out. Timing would be about right on a 2005.
  8. Replies
    9
    Views
    504

    Probably a dumb question, but did those sub...

    Probably a dumb question, but did those sub programs actuallymake it to the machine? Could it have timed out before finishing?
  9. Replies
    6
    Views
    1,061

    I got the file downloaded. Looking at the...

    I got the file downloaded. Looking at the drawing, I need to get in from the tail stock end, loosen 10 bolts to pop the drive loose. Then get the motor to orient and get my drive lug set correcty....
  10. Replies
    6
    Views
    1,061

    P.M. sent with my email Thanks

    P.M. sent with my email

    Thanks
  11. Replies
    6
    Views
    1,061

    Mori SL25Y live tool drive

    I have a Mori SL 25Y, while drilling a cross hole with a live tool the coolant ran dry. This stopped the drill and alarmed the machine. I got everything reset and homed out. The problem is that the...
  12. Replies
    6
    Views
    639

    I have only ran these on a CNC. 1. Yes 4TPI...

    I have only ran these on a CNC.
    1. Yes 4TPI would be the correct pitch for a 4 start 16 TPI

    2. Not sure on this one.

    3.On CNC I ran one thread complete, then started again at different Z start...
  13. Replies
    12
    Views
    1,384

    I run a 4" face mill 8000 RPM in aluminum, I...

    I run a 4" face mill 8000 RPM in aluminum, I can't say that the TSC is hitting the inserts, but I can say that flood is not. The wind generated from the face mill makes an air curtain that prevents...
  14. Replies
    11
    Views
    1,178

    Did this machine have a bar feeder hooked up? If...

    Did this machine have a bar feeder hooked up? If so it may be seeing the bar feeder e-stop circuit and throwing other alarms from that.
  15. Replies
    0
    Views
    1,004

    Opinions on 1998 MC-V4020

    I am considering expanding my mill capacity with one of these. Please let me know the good, the bad, and the ugly. Also a ballpark value.

    Thanks
  16. Replies
    6
    Views
    833

    Probably the air line going into the tool eye...

    Probably the air line going into the tool eye that blows on the eye when you are touching off tools. Just a guess though.
  17. I usually sync them with 1 of the chuck open so...

    I usually sync them with 1 of the chuck open so they don't fight. May not be necessary.
  18. Only thing I can see, and I'm not sure it...

    Only thing I can see, and I'm not sure it matters, is the G50Z line. I use G50 W-[#102]. Just be careful that it is shifting the offset in the right direction.
  19. T0121.02G0G40(TRANSFER) M306(SUB CHUCK OPEN)...

    T0121.02G0G40(TRANSFER)
    M306(SUB CHUCK OPEN)
    G99G18
    G28U0.
    G0Z0.
    G0B-16.
    G97M3S50
    M358(AIR BLOW)
    M5
    M200
  20. Hi Mike. It is looking for one to be made and one...

    Hi Mike. It is looking for one to be made and one not. If I remember correctly you can use a wench, or any piece of steel to see if they are working. Mine have lights on the side of them for when...
  21. Replies
    8
    Views
    1,376

    Low hydraulic pressure might be a phase issue,...

    Low hydraulic pressure might be a phase issue, which could cause the e-stop. switch 2 legs and see if you get pressure
  22. Replies
    61
    Views
    2,661

    Glad I could help. The funny thing is the 100...

    Glad I could help. The funny thing is the 100 Integrex does not have this file. It doesn't seem like it does much, but I think it is more that it is looking for that sub program to run and not...
  23. Replies
    61
    Views
    2,661

    Yes I know it doesn't seem like it does any good,...

    Yes I know it doesn't seem like it does any good, but that is what fixed it. Had the same thing happening, it would change tools and seemed like it completed, but would just sit there.
  24. Replies
    61
    Views
    2,661

    You have to go into the windows side and get into...

    You have to go into the windows side and get into the c drive. You will find a bunch of folders, open up the T_PLC PROGRAM folder. There should be a G code program 9000

    G91G01Y-0.01
    G01Y0.0101...
  25. Replies
    61
    Views
    2,661

    Be very careful here. Parameters from a like...

    Be very careful here. Parameters from a like machine are a good start, but the ladder can be very different with options that you do or don't have. Also there are different versions of the ladder for...
Results 1 to 25 of 151
Page 1 of 7 1 2 3 4