Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Bluejeep

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    17
    Views
    1,333

    I would contact flex hone. see if they have a...

    I would contact flex hone. see if they have a something.
  2. This is why it's handy to have metric set of...

    This is why it's handy to have metric set of collets on hand.
  3. Replies
    25
    Views
    1,415

    try to find thru coolant for your cnmg,like...

    try to find thru coolant for your cnmg,like Seco's jetstream or LMT"point blank"direct flow.
  4. Replies
    10
    Views
    1,210

    Is that a surface grinder sitting just to the...

    Is that a surface grinder sitting just to the right of it? to me that seems like a bad idea.
  5. I've been using a pair of Skullcandy Crusher for...

    I've been using a pair of Skullcandy Crusher for the past year and am very happy with them. they have memory foam ear cushions which work well with glasses. A full charge will last 8+ hrs.looks like...
  6. Over the ear bluetooth headphones. bonus is some...

    Over the ear bluetooth headphones. bonus is some passive sound protection and I can hear my phone and pick it up right thru the headset. I just stream pandora, local radio or podcasts throughout the...
  7. Lay the tube along a t slot. clamp the bottom of...

    Lay the tube along a t slot. clamp the bottom of tube bore to table. for good result both ends need to get clamped
  8. I had a similar problem after suffering a stroke...

    I had a similar problem after suffering a stroke a few years ago. here is a HF engine hoist I crudely modified to lift vises and indexers in/out of my vmc. used what I had lying around for a...
  9. They are in IL. I just troubleshooted over the...

    They are in IL. I just troubleshooted over the phone and ended up shiping the control out to them.
  10. ZPS came thru. I have my Tree back up and...

    ZPS came thru. I have my Tree back up and running. Very happy with the results and price.
  11. I Just had trouble with my Tree 750 with a...

    I Just had trouble with my Tree 750 with a pc2100, troubleshooted last week with ZPS- CNC USA. I ended up sending the controller out to them, they had it fixed in a day and it should arrive back...
  12. Replies
    6
    Views
    1,103

    A dedicated big drill index, just for the lathe...

    A dedicated big drill index, just for the lathe is nice, as is a hex wrench set..
  13. What's the inside angle? Harvey sells chamfer...

    What's the inside angle? Harvey sells chamfer cutters and runner cutters in all sorts of tight angles. maybe you get lucky and they have a stock size that would work.
  14. I found an old contact to zps usa , pulled the...

    I found an old contact to zps usa , pulled the control and sent it off to them.
  15. Need a repair tech recommendation New England area

    I am in need of a repair tech. that might be familiar with a pc2100 control. I have a "System Fail 4000f" error halfway thru boot up. machine is a 1999 Tree VMC750. ran fine yesterday.
  16. Replies
    21
    Views
    2,539

    Are you chamfering the holes before tapping. ...

    Are you chamfering the holes before tapping. that really helps on form taps. especially with a floating tap holder.
  17. Replies
    23
    Views
    3,502

    my guess would be they were using a mt shank...

    my guess would be they were using a mt shank drill that was not seated well. deep holes in delrin are not a problem just don't drill past the flutes that's a recipe for melt. peck drill and some...
  18. Replies
    12
    Views
    1,198

    mill 1/2 way from each side so you don't have to...

    mill 1/2 way from each side so you don't have to use long tooling. I would start with a 1/2" dia. solid carbide rougher. make sure you bolt down the center slug. HARD SCALEMILL ROUGHER I would...
  19. Mcmaster you can get it in .06 and .08 wall by...

    Mcmaster you can get it in .06 and .08 wall by the foot.
  20. Replies
    15
    Views
    1,550

    My guess from the sheet surface from post #8 pic...

    My guess from the sheet surface from post #8 pic 2 is the black polycarbonate pic 3 is black Acetal. Also polycarbonate machines ok, just sensitive to heat, and notch sensitive.
  21. Replies
    21
    Views
    2,557

    really you should be able to get a proper tap in...

    really you should be able to get a proper tap in just a day or 2 why mess with crappy hand tap.
  22. Replies
    50
    Views
    3,262

    :stirthepot: Material: Steel might as well...

    :stirthepot: Material: Steel might as well say Material: metal
  23. Replies
    49
    Views
    3,438

    Reminds me when the curved part of the dipstick...

    Reminds me when the curved part of the dipstick tube rusted out on my ford explorer and I was bamboozled when checking and trying to top up oil before a long trip. after adding 3 or 4 quarts with no...
  24. Replies
    50
    Views
    3,262

    As Jonny 5 would say "need more input" not enough...

    As Jonny 5 would say "need more input" not enough info to make part. It looks like there is more drawing missing as it looks like a cross section view.
  25. I would think with your shop space a bar puller...

    I would think with your shop space a bar puller would make more sense than a bar feeder. and something with a parts catcher. Also don't get too caught up in chuck size as you will probably want to...
Results 1 to 25 of 480
Page 1 of 20 1 2 3 4