Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: tobnpr

Page 1 of 30 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    419

    Not going to matter with a brake on the muzzle...

    Not going to matter with a brake on the muzzle
    The crown will be covered with carbon in short order.
    I've always used Oxpho to touch up crowns on blued rifles.
  2. Replies
    4
    Views
    438

    I've always mounted on the back of the lathe,...

    I've always mounted on the back of the lathe, it's out of the way and easy to attach a bracket to the back of the saddle to drive the read head, mount a long stick of aluminum angle over the top to...
  3. Replies
    5
    Views
    433

    Not familiar with the earlier headstocks, but...

    Not familiar with the earlier headstocks, but later 9's have shim packs that can be "adjusted" (remove shim(s)) to obtain correct clearance. You checked by lifting up with a bar through the spindle?...
  4. Replies
    13
    Views
    1,107

    Easy-peasy fix... Just make a 1/2" adapter...

    Easy-peasy fix...

    Just make a 1/2" adapter plate for the base. This will get your center height to the correct 5".

    Almost did something similar with a 1" plate to get an extra 9A tailstock to...
  5. Replies
    24
    Views
    2,193

    I've bought all my thread mikes off Fleabay,...

    I've bought all my thread mikes off Fleabay, mostly Starretts with a couple Scherr-Tumico.

    Good buys can be had if you're patient, I've mostly paid $40-$60 each, a fraction of new.
  6. Replies
    7
    Views
    1,055

    You want minimum .020 over bullet diameter. My...

    You want minimum .020 over bullet diameter.
    My experience is that overbore isn't as critical to performance as some think.
    Plenty of suppressors are used universally to fit .22 cal and .30 cal....
  7. Bob Pastor's "Viper" fixture is pretty much the...

    Bob Pastor's "Viper" fixture is pretty much the standard bearer for this.

    Simple design, easy enough to machine. If you're going to DIY, may as well make one fitted to a backplate and avoid the...
  8. Replies
    49
    Views
    4,912

    I have a +/- century old Steptoe horizontal mill...

    I have a +/- century old Steptoe horizontal mill that had been converted to a vertical with a Tree head that I bought last year.

    The top surface of the table ways had round recesses, 4 each side,...
  9. Replies
    31
    Views
    2,605

    Off an aircraft carrier :eek:? Jeez...I can't...

    Off an aircraft carrier :eek:?
    Jeez...I can't imagine a rudder post that size. IIRC those on the 40'er I owned were all of 1-1/2".
    Yard that I used, used flame treatment for straightening. Wouldn't...
  10. Replies
    7
    Views
    1,703

    Add me to the list that would like to know... I...

    Add me to the list that would like to know...
    I have a Tree MH4 head (same as 2UV) and was never able to figure it out.
    Didn't want to tear into it when I was cleaning up the machine when I got it...
  11. Replies
    49
    Views
    4,912

    Evaporust is on Amazon...:) I can appreciate...

    Evaporust is on Amazon...:)

    I can appreciate the old american iron "syndrome"- with SB and Sheldon lathes, and an old Steptoe horizontal that had been converted to vertical.

    I've been looking...
  12. Replies
    18
    Views
    1,559

    ^^^ Thanks, I'll dig out the MSC "big book" and...

    ^^^
    Thanks, I'll dig out the MSC "big book" and see if they have anything.
  13. Replies
    2
    Views
    685

    Tree mill collets not releasing?

    Learning the ropes on using the Tree collets- seems there's a fine line between getting the collet tension tight enough so that the cutter won't break loose under heavy cuts, and not so tight it...
  14. Replies
    18
    Views
    1,559

    To clarify, this was converted to vertical...

    To clarify, this was converted to vertical (probably 1970's or '80's) with a Tree head- so there is no existing drive unit; the original spindle and drive shafts are still there but no pulleys,...
  15. Replies
    39
    Views
    2,551

    When I repowered my lathe with a VFD it gave me...

    When I repowered my lathe with a VFD it gave me the excuse to do just that. Needed a power switch for the VFD (the spindle is controlled via the same drum switch wired into the low voltage controls),...
  16. Replies
    18
    Views
    1,559

    Thanks for the input, gentlemen. After taking...

    Thanks for the input, gentlemen.

    After taking another look at this, I'm thinking it probably makes more sense to work the other end of the table.
    The screw extends through the endplate at the...
  17. Replies
    18
    Views
    1,559

    Power feed for an old horizontal mill table?

    All of the commercial power feed units I see are designed to fit BP's and clones...
    Not owning a BP means I have no clue how the drive is set up.

    This is the business end of an ancient (early...
  18. Not just the spindle wicks for cripes sake! If...

    Not just the spindle wicks for cripes sake!

    If the lathe hasn't been torn down, cleaned, and ALL felts replaced in 75 years... it's only 65 years overdue.

    Felts get hard, varnished, and will...
  19. Replies
    8
    Views
    872

    Any size flat drive belts by Al Bino Industrial...

    Any size flat drive belts by Al Bino Industrial Belting | Machine belts supplier
  20. Thread: Best end mills

    by tobnpr
    Replies
    12
    Views
    860

    Most of the guys here have forgotten more about...

    Most of the guys here have forgotten more about machining than I know, but I'll take a stab at this.

    Question is way overbroad.
    You seem to be referring to carbide, is HSS not practical?
    ...
  21. Replies
    7
    Views
    1,298

    Plenty of open-source dimensional drawings...

    Plenty of open-source dimensional drawings (including CAD) online for these- but you'd need to write your own code for CNC.

    Free CAD Designs, Files & 3D Models | The GrabCAD Community Library
  22. Replies
    4
    Views
    1,036

    I'm licensed as a manufacturer- but primarily do...

    I'm licensed as a manufacturer- but primarily do riflesmithing and not sales/transfers- so the paper book works fine for me.

    There is a website- "FFL's Only" with members comprised solely of...
  23. Replies
    24
    Views
    1,214

    I bought F1 felt sheeting from McMaster and made...

    I bought F1 felt sheeting from McMaster and made my own from 3/16", 12 x 12, for mine.

    McMaster-Carr

    I bought the felt rope for the spindle wicks elsewhere (can't recall now); point being...
  24. Technology advances in this area have really been...

    Technology advances in this area have really been amazing over the past few years.
    Variable speed, inverter powered (DC) compressors, etc. with incredible energy efficiency/SEER ratings.

    If the...
  25. Thread: Lathe bench

    by tobnpr
    Replies
    40
    Views
    3,638

    Consider... How much is the lathe actually going...

    Consider...
    How much is the lathe actually going to be used?

    There's always the issue that wood compresses, and changes dimension with temp and humidity.

    I love the pictures I see of...
Results 1 to 25 of 739
Page 1 of 30 1 2 3 4