Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: sudsy55

Page 1 of 17 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    13
    Views
    427

    Yes I get that often if I have been doing a lot...

    Yes I get that often if I have been doing a lot of editing in a program. I only try it a couple of times then just rewrite that unit and 9 times out of 10 it fixes the problem
  2. Replies
    1
    Views
    319

    Modify the pump to take a readily available seal

    Modify the pump to take a readily available seal
  3. Replies
    0
    Views
    313

    Probe problem on H 400

    G'day all, trying to get the probe working on my H400. It had a probe setup already but the induction module had been crashed into prior to me buying the machine so I've never had a probe working on...
  4. Replies
    2
    Views
    561

    Shame the shipping to Australia is so bloody...

    Shame the shipping to Australia is so bloody expensive
  5. Not that I have found but maybe someone that has...

    Not that I have found but maybe someone that has had proper training may know. I am pretty much self taught so still very green
  6. Use your edge finder and take it to the X...

    Use your edge finder and take it to the X coordinate of your job. On the command screen look at the numbers for the X position. This is your X zero + or - half the diameter of the edge finder. This...
  7. You'll work it out in no time Mick. I'm only a ph...

    You'll work it out in no time Mick. I'm only a ph call away to get you started. Or I might come for a bit of a ride lol
  8. I think you've confused everyone with these old...

    I think you've confused everyone with these old machines Mick lol
  9. Are you getting any errors or does it just...

    Are you getting any errors or does it just unclamp and sit there? If just sitting there you need to check if its getting the index signal. Should be able to see this on the ladder
  10. How did you go? Get it sorted?

    How did you go? Get it sorted?
  11. Replies
    20
    Views
    2,080

    Might pay to flip the breakers off then back on....

    Might pay to flip the breakers off then back on. Some types of breakers can look like they are on but have actually tripped
  12. Replies
    17
    Views
    2,034

    Actually I think there is an epprom you will need...

    Actually I think there is an epprom you will need but after that the other options may be just parameter related. It is on the memory modules (lower left side of controller. I can't remember the...
  13. Replies
    17
    Views
    2,034

    Knowing what they're like there is probably...

    Knowing what they're like there is probably another secret code you need to get into it. Try rubbing your belly clockwise, your head ccw while standing on one leg on a bungy cord in the middle of the...
  14. Replies
    17
    Views
    2,034

    Interesting to see the outcome

    Interesting to see the outcome
  15. Replies
    4
    Views
    960

    And I do that how exactly???

    And I do that how exactly???
  16. Replies
    4
    Views
    960

    I have tried all different combinations. Changed...

    I have tried all different combinations. Changed a couple of parameters associated to chamfering and still the same
  17. Press MNT PressPLC PressPREG Pressthe clear...

    Press MNT
    PressPLC
    PressPREG
    Pressthe clear key once (top rh corner} (this puts the keypad in letter mode)
    Press 6 9That should give you ( R) in the brackets at the bottom
    Punch in 2390 (this...
  18. You press the management button then go to PLC I...

    You press the management button then go to PLC I think. Will check tomorrow
  19. Change it with machine running is the best but...

    Change it with machine running is the best but can be done with machine off if you get it done in short time
  20. These are the parameters on my H400 so I don't...

    These are the parameters on my H400 so I don't know if yours would be the same but being M32 I would say they should be the ones.R2390is the distance between the switch signals. You will have to...
  21. Replies
    4
    Views
    960

    Doing my head in

    G'day all,
    have just recently started working my H400 with M32 controller. I'm having trouble getting the chamfer program to work. Have tried different size tools and adjusted a couple of...
  22. Its done in the R parameters. Not in the shed at...

    Its done in the R parameters. Not in the shed at the moment so not sure which one offhand. Takes a little bit of mucking around and measuring but not too difficult
  23. Thread: M32 FLD Error

    by sudsy55
    Replies
    3
    Views
    660

    Will usually only boot from disc if battery is...

    Will usually only boot from disc if battery is going flat. There is a battery in the module beside the FDD as well as the big 6v battery and another on one of the boards(can't remember which one...
  24. Replies
    13
    Views
    964

    Not sure if the M plus is similar to M32 but if...

    Not sure if the M plus is similar to M32 but if when you are writing the block you have the options on the bottom. If you select other it will bring up more options with index being one of them. Like...
  25. Replies
    13
    Views
    964

    Why have you got the centre drill as a manual...

    Why have you got the centre drill as a manual program? In the Mazatrol tapping cycle you have the centre drill, tapping drill and tap in the one cycle.
Results 1 to 25 of 418
Page 1 of 17 1 2 3 4