Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: eKretz

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Is this a free to a good home kind of thing?...

    Is this a free to a good home kind of thing? Mighty kind of you.
  2. Replies
    7
    Views
    469

    If he is positive about that 30% number and has a...

    If he is positive about that 30% number and has a graduated syringe he can just fill it 100% with a light oil while the bearing is lying on a piece of painter's tape or something to seal the bottom....
  3. Replies
    7
    Views
    469

    Here you go: How to Calculate Grease Quantity...

    Here you go:

    How to Calculate Grease Quantity and Frequency for Bearings

    If you really need that 30% here's a PDF from Klueber that is a little more detailed:
    ...
  4. While it is true that the calculators for nose...

    While it is true that the calculators for nose radius and feed rate are very useful, they don't always tell the whole story. You still need to be making it "shiny" or you're likely producing a torn...
  5. So where's the little sword to go with it?! :D ...

    So where's the little sword to go with it?! :D

    Nice work.
  6. If you are running HSS, use the opposite. Slow it...

    If you are running HSS, use the opposite. Slow it way down and take a very light cut with water based coolant. The chips will come off like foil and you'll get a very fine finish. I've gotten an 8 Ra...
  7. Yeah as long as you have your cutting speed up...

    Yeah as long as you have your cutting speed up high enough you can pretty easily turn a 32Ra finish. If it's not quite shiny enough give it a quick spin with lightly oiled brown scotch-brite and it...
  8. I got a couple good shots of Monarchs while...

    I got a couple good shots of Monarchs while mowing a 25 acre field. They were everywhere. Along with a bunch of other critters.

    278885

    278887

    278886
  9. Replies
    26
    Views
    6,201

    More likely the O.P. discovered that he fucked up...

    More likely the O.P. discovered that he fucked up somewhere and felt like an idiot, so didn't post an update about what he was doing wrong. I've used a lot of Kurt vises and never had one with a...
  10. Thread: Thread Quality

    by eKretz
    Replies
    46
    Views
    3,199

    A place I worked at had a guy who did exactly...

    A place I worked at had a guy who did exactly that as well. Same reasoning.
  11. Replies
    32
    Views
    2,171

    Errr... Someone missed the joke. :D

    Errr... Someone missed the joke. :D
  12. Replies
    32
    Views
    2,171

    Isn't that what needle nose pliers are for? :D

    Isn't that what needle nose pliers are for? :D
  13. Replies
    24
    Views
    2,447

    Haha, that totally reminds me of Hitchhiker's...

    Haha, that totally reminds me of Hitchhiker's Guide. :D
  14. Replies
    0
    Views
    252

    Anyone know anything about Etamic CSZ 400?

    Just nabbed this thing from Mike Henry who offered it for the cost of shipping. Wasn't working when I received it but that was just a conductor that came loose internally on the power connector. Now...
  15. Replies
    43
    Views
    2,006

    Bob...nobody's perfect. It sounds like your dad...

    Bob...nobody's perfect. It sounds like your dad tried though. I do the same as I'm sure most (I won't say all) fathers do. Sometimes you blow it. As long as Dad doesn't go overboard and is man enough...
  16. Replies
    43
    Views
    2,006

    I dunno. To me, common sense means someone can...

    I dunno. To me, common sense means someone can figure out the things that are or should be common knowledge without being hand held through them. Who defines what is or should be common knowledge and...
  17. Replies
    43
    Views
    2,006

    I'd start by making him a block of steel with...

    I'd start by making him a block of steel with several each of different sizes of threaded holes and a handful of bolts. Have him tighten them until they break off to get a good feel for that point....
  18. Replies
    24
    Views
    2,447

    We had some good hand written ones. Above the...

    We had some good hand written ones. Above the squirrel cage on the drive motor and belts for an ancient 48" lathe: "Live animals inside" :D
  19. Replies
    39
    Views
    2,488

    Tci, You get an atta boy for explaining...

    Tci,

    You get an atta boy for explaining yourself like a man. I also completely agree with Rob that you'd have gotten a lot different response here if you had been straight shooting from the...
  20. Yeah .001" ain't happening. Unrealistic...

    Yeah .001" ain't happening. Unrealistic expectations abound.
  21. Larger work always pays better. The fewer the...

    Larger work always pays better. The fewer the shops that do the work, the more expensive it is. Supply and demand just like everything else. It also costs more to buy larger machines, larger tooling...
  22. Replies
    8
    Views
    810

    Looks like it says Taiwan right on it in the one...

    Looks like it says Taiwan right on it in the one picture. Quality looks pretty decent to me.
  23. Replies
    39
    Views
    2,488

    And here comes the snark...:rolleyes5: Another...

    And here comes the snark...:rolleyes5: Another one of THOSE noobs.
  24. Looks like a good place to sit and watch while...

    Looks like a good place to sit and watch while having the morning cuppa joe.
  25. Replies
    39
    Views
    2,488

    Probably would have been better to go with...

    Probably would have been better to go with sliver-removing tweezer.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4