Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: malkey

Search: Search took 0.00 seconds.

  1. Replies
    28
    Views
    3,400

    I have bored 20 inches before with a 2in bar....

    I have bored 20 inches before with a 2in bar. Milled a perpendicular slot in the end of the bar 1/2 wide for a small shank turning tool like you might use on a hardinge lathe, if you only have RH...
  2. Replies
    51
    Views
    5,280

    I recently made a small tap handle, #4-0.25,...

    I recently made a small tap handle, #4-0.25, spring loaded. Did everything on a HLV and Bridgeport, also made some small swivel "cannon" keychains from stainless. In this trade the possibilities are...
  3. Replies
    5
    Views
    786

    Not certain but would you be able to use a WNMG...

    Not certain but would you be able to use a WNMG holder and just change the screw?
  4. Replies
    12
    Views
    1,463

    If you cant find a tool just grind it from HSS. ...

    If you cant find a tool just grind it from HSS. I've ground plenty of small threading and boring bars from 1/4 carbide and HSS. If you are cutting plastic they will last a lifetime.
  5. Will do, thanks again!

    Will do, thanks again!
  6. Only a replacement parts manual

    Only a replacement parts manual
  7. Now that I have that, anybody have a clue as to...

    Now that I have that, anybody have a clue as to the program one would need to write for the B&S 1236 Micromaster?
  8. Thanks Converterking, I will look in to that.

    Thanks Converterking, I will look in to that.
  9. GE Fanuc Series One Programmable Control Help

    Recently I posted about working on a Brown and Sharpe 1236 Micromaster and after all the issues with the hydraulic system have been fixed I am on to the next problem...

    All of the solenoid valves...
  10. Replies
    6
    Views
    1,327

    **Update** Selector switch set to rapid and I...

    **Update** Selector switch set to rapid and I manually pushed the left solenoid valve in to move the head into the rear so now I am able to access the crossfeed nut. It seems to have a decent amount...
  11. Replies
    6
    Views
    1,327

    Update** I have corrected the leak in the valve...

    Update** I have corrected the leak in the valve body by pulling out all the pistons and using scotchbrite to clean up the bores so everything can move freely, reassembled making all 4 new gaskets.
    ...
  12. Replies
    3
    Views
    612

    I have seen a similar error while using a...

    I have seen a similar error while using a accu-rite DRO, take the Y scale off and use a Q-tip soaked in high % alcohol and clean the glass on both sides until the tip is clean. When you reassemble be...
  13. Replies
    11
    Views
    1,383

    Other than using the soap which will help a lot,...

    Other than using the soap which will help a lot, after the final tumble there is a corn cob media that you tumble in a dry drum and that will give the parts an extra shine.
  14. Replies
    6
    Views
    1,327

    Here is a picture of the machine so you have a...

    Here is a picture of the machine so you have a reference.
    257095
  15. Replies
    6
    Views
    1,327

    There is just the one handle for the crossfeed...

    There is just the one handle for the crossfeed and it has a fine adjustment knob.
    The one that is a push/pull is for the table traverse which is the side to side motion.
  16. Replies
    6
    Views
    1,327

    B&S 1236 with control crossfeed issue

    Having multiple issues with this machine, one of which is the crossfeed handle will move the head towards the operator but not the other direction.
    There is an access panel on the front of the...
  17. Feeler SOM-510 Second Op Lathe - Need Wiring Diagram

    I have a 1984 SOM510 S/N-73051, 220V lathe and no wiring diagram with some missing parts in the wiring cabinet. Any leads to a wiring diagram would be much appreciated.
Results 1 to 17 of 17