Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: markp

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    563

    Well, I tried to use the drive duplicator today...

    Well, I tried to use the drive duplicator today to make a disc copy and now the original drive which was mostly working is not recognized buy the system. The drive duplication seems to have failed as...
  2. Replies
    15
    Views
    1,284

    I changed the PLC instructions: 1.Set S4 on 840D...

    I changed the PLC instructions: 1.Set S4 on 840D NCU to position #1. to 1. Set S4 on 840D NCU to position #2 and I was able to load the PLC archive. Now I can do about everything except add tools to...
  3. I looked around further online and found the 840D...

    I looked around further online and found the 840D manual for dummies! Just search SINUMERIK 810D/840D/840Di Beginner's Manual:. Its a old SinuTrain manual for students for the older versions of the...
  4. Tool setup for DMG DMC103V with 840D control

    Im learning to use my new to me DMC103V. I downloaded the tool management manual and its 450 pages long!! Ive run many CNC controls since I started using CNC machine tools in 2000 but Ive never seen...
  5. Replies
    15
    Views
    1,284

    I tried this reset procedure and I was able to...

    I tried this reset procedure and I was able to reset the NCK but when I tried to reset the PLC I got the error "No PLC memory reset possible". I tried the matching archive and a later one, same...
  6. Replies
    6
    Views
    563

    Hanermo, I tried to send a PM but your box is...

    Hanermo, I tried to send a PM but your box is full. Great if you could do this for me and the machine. I can dropbox the factory floppies...DMG is saying the control is too old to make a new HD for....
  7. Replies
    6
    Views
    563

    Rather than deal with all the drive cloning...

    Rather than deal with all the drive cloning rigamarole, I ended up buying a Startech bit for bit 2.5" IDE to 2.5" IDE forensic drive duplicator. They still make these new! 225$. I plan on making a...
  8. Replies
    4
    Views
    482

    That would be great. Under services I have two...

    That would be great. Under services I have two cycles in the user cycle folder. One is CYCLEGRA and the other is DPWP.
  9. Replies
    6
    Views
    563

    Hanermo, Tried to send a PM but your inbox is...

    Hanermo, Tried to send a PM but your inbox is full.Thx
  10. Replies
    4
    Views
    482

    Just found a note in the paper work from a DMG...

    Just found a note in the paper work from a DMG tech. "added m codes 90 91 92". Looks like it might be the same handwriting as the receipt for the laser install but was mixed in with the other...
  11. Replies
    1
    Views
    1,005

    I have operator manuals and electrical schematics...

    I have operator manuals and electrical schematics for my dmc103v. Do you still need them?
  12. DMG users with Siemens control and laser toolsetter/tool breakage option how to use?

    I recently purchased a 2000 DMG DMU103V with Siemens 840D control. It has the laser tool measurement system installed with the options of tool breakage detection and tool measurement installed...
  13. Replies
    6
    Views
    563

    Sounds good, Ill PM you. Thx!

    Sounds good, Ill PM you. Thx!
  14. Replies
    6
    Views
    563

    Creating a new system disc for Siemens 840D

    I recently purchased a 2000 DMG DMC103V. Im getting an mdbbe.ini error on boot and want to recreate the system drive from the original factory discs. I have a win 95 disc and two floppies, One dics...
  15. Replies
    4
    Views
    482

    DMG DMC103V How to use Blum laser system

    Im installing a new to me DMC103V machine with 840d control. A Blum laser tool measurement system was installed and calibrated by DMG a few months after purchase. I have all the factory documentation...
  16. Replies
    15
    Views
    1,284

    Also wrote a short program with spindle speed...

    Also wrote a short program with spindle speed changes and linear moves and the machine will run programs from the hard drive OK.
  17. Replies
    15
    Views
    1,284

    There is one key with two down arrows and 1...n...

    There is one key with two down arrows and 1...n above it. That key doesnt do anything at least in mode 3 and bottom key straight up when in MDI or "machine". Channel switching seems to be disabled on...
  18. Replies
    15
    Views
    1,284

    Machine made it back to my shop! Cant do a final...

    Machine made it back to my shop! Cant do a final install until I sell the machine its replacing but its in its temp location. All manual functions work, I can reference the axis, jogging, spindle in...
  19. Best voltage output for a vmc when output from transformer taps are either low/high

    Installing a DMG DMU103V euro vmc nominal voltage is 400. I have a delta to wye 230-400volt transformer. Ground is bonded to X0 on output side. Ive got 240 here with a hot leg. Im seeing 436 volts on...
  20. Replies
    15
    Views
    1,284

    Machine is being delivered tomorrow. It actually...

    Machine is being delivered tomorrow. It actually is an 840D. There were two different receipts for the machine from DMG. Seems it was originally delivered from germany with the table locking pin in...
  21. The plate I got from Yang was aluminum with rivet...

    The plate I got from Yang was aluminum with rivet holes. Looks like it was silkscreened onto the plate. I put a lexan sheet over the plate using silicone adhesive to protect it
  22. FYI, you can still buy the speed/gear/threading...

    FYI, you can still buy the speed/gear/threading name plates from Cadillac/Yang USA distributor in LA for about 25$. I bought one for my Mori clone Cadillac 2260 two years ago.
  23. Replies
    15
    Views
    1,284

    My mistake, Its actually an 810D. Looking at the...

    My mistake, Its actually an 810D. Looking at the front panel I thought it was an 840D. Owners didnt know. I saw that there were 2 floppy discs in the cabinet. one was the V24 file transfer disc and...
  24. Replies
    15
    Views
    1,284

    Thanks that’s great step-by-step information. I...

    Thanks that’s great step-by-step information. I was able to boot the machine a couple times and get servo enabled and jog I was able to move the axis and block the spindle. Then I tried to do a...
  25. Replies
    15
    Views
    1,284

    Yes thats all there. I had no access to the...

    Yes thats all there. I had no access to the printed docs so looking around online.
Results 1 to 25 of 486
Page 1 of 20 1 2 3 4