Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: jancollc

Page 1 of 60 1 2 3 4

Search: Search took 0.02 seconds.

  1. Technically the "read only" only attribute only...

    Technically the "read only" only attribute only applies to files. If you have a folder marked read only, you can still rename it, delete it, add files, etc. Windows only uses the read only and system...
  2. Replies
    830
    Views
    57,673

    It all depends on the airspeed and how far out of...

    It all depends on the airspeed and how far out of trim the horizontal stab is to begin with. There is a point where it becomes impossible to overcome the aerodynamic forces on the stab.

    737 Vmo is...
  3. This might be a symptom of a failing USB drive,...

    This might be a symptom of a failing USB drive, so get it backed up.

    You can use the attrib command to remove the write protect on a volume. From a command prompt, the syntax is:

    attrib -r...
  4. Right click the folder. Select properties....

    Right click the folder. Select properties. Uncheck "read only".
  5. Replies
    15
    Views
    853

    You can do it, but it will be slow. I have a...

    You can do it, but it will be slow.

    I have a 3/4" Kennametal 2-flute indexable that would make short work of that hole. With 300 pcs, the tool pays for itself in time saved...
  6. Thread: Recession?

    by jancollc
    Replies
    68
    Views
    3,787

    The global economy has been slowing since the...

    The global economy has been slowing since the middle of last year. The Brexit confusion has hurt the EU, the trade war has hurt the Asian economies. Both affect the US, but we have done better than...
  7. Replies
    15
    Views
    853

    OP has 300 pieces to do. The right strategy is to...

    OP has 300 pieces to do. The right strategy is to approach it in a way that minimizes hand work and still allows a decent tool life.

    Hand grinding 300 parts is not the way...
  8. Replies
    15
    Views
    853

    ^^^ That's how I would do it. If the OP uses...

    ^^^ That's how I would do it.

    If the OP uses an endmill, I'd conventional the first pass around- it'll get under the crap and be easier on the cutter.

    edit: Lol. beat me to it. Agree, climbing...
  9. Replies
    5
    Views
    436

    That looks like the animal, but it's not SS. ...

    That looks like the animal, but it's not SS.

    They do show one in stainless at a slightly higher price...:eek:

    PKR-X11B/08SS Hydraulic Hose, Fittings & Assemblies STAINLESS STEEL HYDRAULIC...
  10. I replaced the 4 D cells last month in my...

    I replaced the 4 D cells last month in my Chevalier.

    The year-old batts were still reading ~5.9 volts.
  11. Replies
    17
    Views
    1,537

    It was hard to steer until you got it going. That...

    It was hard to steer until you got it going. That was the main reason I bought a modern Toyota- it's just so much easier to maneuver inside the shop with power steering and automatic trans.
    ...
  12. I replaced a QR25 with a screw for the noise,...

    I replaced a QR25 with a screw for the noise, that Quincy was bulletproof.
  13. Replies
    30
    Views
    1,951

    I like that Berco gage. These work good too. ...

    I like that Berco gage.

    These work good too.

    Internal Caliper Gage | 57-015-072 | Travers Tool Co., Inc.
  14. The little cover is just to keep chips out. It...

    The little cover is just to keep chips out. It usually has 3 screws holding it in.

    After that cover is removed, you will need the wrench to remove the chuck from the drawtube.

    Here's the manual...
  15. Replies
    50
    Views
    4,282

    I have Oemeta Novamet 100 in 2 machines (VMC's)...

    I have Oemeta Novamet 100 in 2 machines (VMC's) right now. Both machines run pretty much nothing but aluminum.

    One is at 18 months and the other one is at 8 months. No stink, no rust- but watching...
  16. Replies
    1,519
    Views
    56,224

    And only a 79% tariff! Conventional bikes have...

    And only a 79% tariff!

    Conventional bikes have it better, the tariffs are only 48%...
  17. Replies
    11
    Views
    475

    Climb up and look. There should be a provision...

    Climb up and look. There should be a provision for a wrench on the shaft to crank it by hand. You have to release the brake first, look for a lever on the side.
  18. Replies
    3
    Views
    440

    Yeah, the 5" I have is clearly not a pipe spec-...

    Yeah, the 5" I have is clearly not a pipe spec- it's just an out of spec (oversize) tube. 5" extruded tube does not have 1/8" of tolerance on the OD.

    The material I need to order comes from LA. I...
  19. Replies
    50
    Views
    4,282

    I looked at that "The Cleaner" from Spartan. pH...

    I looked at that "The Cleaner" from Spartan. pH 13.0-13.5 :eek:

    No wonder it cuts the grease.

    My SV2412 is a box way machine and it puts a lot of way oil in the coolant tank, which emulsifies...
  20. sucks ....

    sucks



    ....
  21. Replies
    3
    Views
    440

    ASTM B221 vs. ASTM B429

    I'm about to start a project that uses a lot of .250 wall 6061 tubing. I'll use sizes from 1-1/2" to 6".

    I have some 5' long pieces of tube that I will not be using- planning to order everything...
  22. They mail an invoice, I mail a check to...

    They mail an invoice, I mail a check to California. I've never even been to the store in Portland- everything comes to me.

    Call the corp office- 925-443-8665 and ask for someone in AR. Tell them...
  23. Tool Supply doesn't have much inventory,...

    Tool Supply doesn't have much inventory, everything I have bought from them had to be ordered.

    Why don't you just setup an account with Western? I get decent pricing from them, a phone call and...
  24. Replies
    64
    Views
    3,904

    I buy my cutting tools from Western. But a lot of...

    I buy my cutting tools from Western. But a lot of my miscellaneous stuff comes from McMaster.

    You can specify exactly what you want, but it takes a phone call. I buy an Omron prox sensor from...
  25. Replies
    63
    Views
    3,943

    F-35's have flown combat missions in Afghanistan,...

    F-35's have flown combat missions in Afghanistan, Syria, and Iraq. The Brits have flown them alongside Typhoon in combat missions against ISIS, and Israeli F-35's have flown over Tehran.

    In Red...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4