Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: jz79

Page 1 of 31 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    86
    Views
    5,011

    I suspect his "2 triangle" solution would turn...

    I suspect his "2 triangle" solution would turn out to be the exact same thing you posted in post number 4, it takes 2 triangles to get to the slope angle, once there you still need to calculate 2...
  2. he isn't dealing with subatomic particles or...

    he isn't dealing with subatomic particles or number of falling balls, rather than that during the descent of said balls they may randomly at any given time change mass, gain OR lose for uncertain...
  3. like EG said, this sounds like probability with...

    like EG said, this sounds like probability with uncertainty, meaning, based on previous data you can try and guess with certain amount of probability how the changes in your plants electricity...
  4. Replies
    10
    Views
    417

    anodizing grows perpendicularly to the surface -...

    anodizing grows perpendicularly to the surface - I suspect that is where your "4:1 ratio" comes from, if draw cross section of your thread in cad, add half of the total thickness of to the thread...
  5. Replies
    86
    Views
    5,011

    we have an ironic saying here that roughly...

    we have an ironic saying here that roughly translates to - if you don't know how to apply your knowledge to earn living with it - you go to work a teacher teaching these exact skills

    that slope...
  6. Replies
    86
    Views
    5,011

    I used to be quite good at algebra and geometry...

    I used to be quite good at algebra and geometry back in the school (which wasn't THAT long ago), but the triangle incircle had completely slipped out of my mind...

    Looked up the theorem and the...
  7. Replies
    261
    Views
    16,006

    guys, I think OP got the message already, and the...

    guys, I think OP got the message already, and the more you keep pounding him the sorrier you'll make Frank feel about this and the higher the chance of OP getting one benefit out of this or the...
  8. Fehlmann P18 and P50 deserve mentioning - and...

    Fehlmann P18 and P50 deserve mentioning - and don't be distracted by the round columns, they are the best that is out there in that size/design, capable of light milling, P50 is a 1000kg machine...
  9. I wonder what buzz word will they attach next to...

    I wonder what buzz word will they attach next to their product name when customers will get disappointed in the ULTRA PRECISION level of quality they offer now...

    this isn't the first, seemingly...
  10. Replies
    54
    Views
    3,873

    apart from the other factors - like increased...

    apart from the other factors - like increased amounts of packages overall due to pandemic, there is the thing of the virus itself sticking on surfaces and traveling with stuff to new locations, then...
  11. Trace is what you can use to follow an edge or 3d...

    Trace is what you can use to follow an edge or 3d sketch, but it will not output arcs (most of the time), at least that is what I was able to find out searching AD forums, enabling smoothing and...
  12. Replies
    6
    Views
    406

    personal licence users shouldn't be upset for...

    personal licence users shouldn't be upset for something they have FREE access to, some people will complain about anything free still not being good enough, this forum is a good example when people...
  13. Replies
    34
    Views
    3,238

    had something like this with an alloy steel...

    had something like this with an alloy steel sheet, composition similar to 4140, 2mm thick, it had some mill scale with rust preventative on it and the parts looked similar to yours, they were very...
  14. 16 micron backlash on a screw in a new machine?...

    16 micron backlash on a screw in a new machine? :skep:

    if that is indeed the case, messing around with the counter balance force would just be a band aid on a gangrene infected limb... you could...
  15. Replies
    395
    Views
    14,031

    didn't you say there was some morality involved...

    didn't you say there was some morality involved in this? :D

    the whole concept was quite basic and strategically designed if you think about it - no fees or entry cost and it is right there on your...
  16. Replies
    395
    Views
    14,031

    I wonder how many investors would be there if...

    I wonder how many investors would be there if they couldn't sell the stock they bought for a year or two (and lets imagine there is no way to circumvent this rule), and had to wait for the company...
  17. Replies
    7
    Views
    459

    C11 looks to be the "brown" tantalum in one of...

    C11 looks to be the "brown" tantalum in one of the pics in the first post, below the other tantalum, and it is typical for them to short out on failure, they are sensitive to reverse polarity

    that...
  18. Replies
    7
    Views
    459

    unfortunately the circuit diagram in 1st photo is...

    unfortunately the circuit diagram in 1st photo is not readable, PM forum doesn't support large image hosting, try to find a place to upload high resolution image with a readable diagram and post a...
  19. Replies
    52
    Views
    1,965

    you should first look at the type of the...

    you should first look at the type of the motor/drive combo there is on that machine, it is entirely possible your idea is completely incompatible with the design if it uses something like thyristor 3...
  20. Replies
    5
    Views
    735

    those are Soviet copies based on the universal...

    those are Soviet copies based on the universal mill layout (675 is the most common one), some are closer to Deckel design, others are more like Maho, build quality also tends to vary a lot, here is a...
  21. Replies
    30
    Views
    1,559

    I realize the question was how to drill, not how...

    I realize the question was how to drill, not how to make the end product, but I have to ask - can't you start with a tube? I did a quick search and see that extruded tubes are available in 1.75"OD...
  22. Replies
    19
    Views
    1,174

    that looks like 16k20, they still make them I...

    that looks like 16k20, they still make them I think, smallest one would be around 16x28 in inches and around 6000 pounds - more here if interested 16К20 Станок токарно-винторезный универсальный....
  23. Replies
    13
    Views
    850

    you'll need pads inside for smooth action and to...

    you'll need pads inside for smooth action and to reduce wear, anodizing against anodizing (ptfe impregnated or not) will not last long, and if the tubes are thin and long, there might be an issue...
  24. Replies
    28
    Views
    1,139

    UV most definitely kills this virus, and not just...

    UV most definitely kills this virus, and not just this one, it disrupts DNA if there is no shell surrounding it that can absorb that UV, there are secondary effects also, increased UV helps to...
  25. Replies
    28
    Views
    1,139

    there is one important thing to remember when...

    there is one important thing to remember when comparing daily data with Australia and New Zealand, they have summer there right now, plenty UV to kill the virus quickly in the air

    we had very very...
Results 1 to 25 of 757
Page 1 of 31 1 2 3 4