Search:

Hi Ross,



When I first put my FP2 back together, the motion was tight at the bottom of Z, exactly because of this kind of of misalignment. I've also seen this in Y after repairing from a crash,...

Hi Dennis,

I think what Thanos wrote earlier is most likely. With the relatively light use that you are giving the machine, the only process that will eat the nut is a sharp edge or burr on the...

If you are willing to endure the hassle of international shipping, you can buy one in Germany fairly easily. These ones are expensive, I have seen them frequently for around 7-800 Euro. Not sure if...

Thanks for the photos. They are so heavy that no one wants to use them -- I was once offered one of those for very little money because the guy just wanted to be rid of it. For once, my better...

I haven't seen them like that, would be grateful for a photo. BTW, that's their biggest model, 200mm wide, can you pick it up without a crane?

Nice work Dave! On the originals the hold-down holes are slots not holes, which I prefer because it is faster to mount and remove. How come you did holes?


Sent from my iPhone using Tapatalk

The previous posts are more than 10 years old [emoji4]


Sent from my iPhone using Tapatalk

You can find the Talyvel patents online. They make interesting reading.

The support is done with three fine copper-berillium wires. The design is clever. One of the support wires forms a "V" at...

FWIW, that's what I use on the bevel gears of my Deckel FP2 vertical head. It's overkill, but I had a cartridge on-hand and an expert (Singer) told me it was OK.

Hi Ross,



Thanks for setting me straight on this. I thought that "Universal" meant independent adjustment for each jaw, since that can hold any shape.

Cheers,
Bruce

Here in Germany I have 3 phase 400V @ 32A in my home workshop, so I don't need this for myself. But this looks like a great solution for people who want to run a European 400V/3-phase machine on...

I'm rather busy at the moment so did not reply to your original posting. But I just had a look - if traffic is good the seller is less than an hours drive for me. So I can help out if you still...

That's awful, I'm sorry. Which guy??

I didn't realize that such things were available. I thought that if you want 400V output you need 400V input, because all that a VFD does is provide phase-shifted versions of the input, perhaps at...

Hi Ross,



Sorry that I wasn't clear. I meant the following...

If you move Y as far as possible towards the vertical rotation axis of the Hermle table, the closest you can get to that axis...

I've been too busy to spend much time in the shop recently, but did test the adaptor plate a bit more. The first thing I found was that the two-jaw chuck was badly off-center. In fact it's so badly...

That's for holding a 40mm shell mill or a facing/planing head.

I finished making the adapter plate today. First measured the tapered retaining holes by turning a plug and adjusting the dimensions for good fit, using a felt marker to assess the contact:
...

That's not right. This looks like a Fischer or SFJ spindle. Are you sure that there are no (faded) markings on the body?

A lot of spindle like this have a set of springs inside that preload the...

IMO rklopp has a good point.

I've got my FP2 set up so that I can use either flood coolant (water-soluble oil emulsion) or compressed air/oil mist, but I almost always go with the air/oil mist. ...

Hi Thanos,

Ross will probably give a detailed answer to your question. My understanding is that the slides of the FP3 have more area and better lubrication than on our generation of FP2. They...

Congratulations on finally getting it free! I remember this thread, and was wondering what eventually happened. Thanks for the update.

Dear Buck, by the way, if you look to the left of the grinder, some of those wheels there came from you. They are now fitted to hubs and being used. Thank you! Cheers, Bruce

PS: above, you wrote...

I've got exactly the same:

https://www.practicalmachinist.com/vb/attachment.php?attachmentid=316716&d=1616023040

When I bought mine used, it was pretty gummed up with dried coolant. So take it...

That doesn't look fake to me, looks like it's a business getting rid of some of their machinery, PROKUTEC GmbH in Raubling - Feinmechanik Look under the "Rechtliche Angaben"