Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: adh2000

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    0
    Views
    85

    FS: M and M Moulder Planer

    Precurser to the Williams and Hussey. 6Ē two knife moulder. Cute as a bug. Been sitting in my garage forever needs to move on. Single phase motor. Located in Woodland Hills CA (LA area). $350...
  2. Replies
    10
    Views
    820

    Hmm. Never heard of them. No we do not need a...

    Hmm. Never heard of them. No we do not need a visa to travel to the EU. No we do not need a letter of invitation.

    That address is only a few miles from me I could drive by except I wonít be home...
  3. Replies
    1,595
    Views
    100,706

    Doubtful. The problem with that strategy is...

    Doubtful. The problem with that strategy is always that the electric field is concentrated at the corners. So the insulation breaks down there unless you use thicker insulation which offsets the...
  4. Replies
    6,662
    Views
    155,514

    The "wound collector" article was interesting. ...

    The "wound collector" article was interesting. Thanks for posting that. Unfortunately he didn't offer any solutions. My daughter is a bit like that, not so extreme. I keep hoping she out grows it...
  5. I also don't expect it to work out. Somehow I've...

    I also don't expect it to work out. Somehow I've become old, but 40 years ago I tried to go after a couple "opportunities" like you claim to offer. The problem is the older shop owner expects the...
  6. Replies
    854
    Views
    22,710

    So what happened to COVID herd immunity? Between...

    So what happened to COVID herd immunity? Between those vaccinated plus those recovered we are well beyond what we supposedly needed for herd immunity. Arenít we? And do we need herd immunity for...
  7. Replies
    15
    Views
    1,522

    Diacro not Hossfeld but maybe some useful ideas...

    Diacro not Hossfeld but maybe some useful ideas here:

    https://www.diacro.com/wp-content/uploads/2016/07/Art-Of-Bending_2013.pdf



    Sent from my iPhone using Tapatalk
  8. Looks like preheat is coal. Post heat is dung. ...

    Looks like preheat is coal. Post heat is dung.



    Sent from my iPhone using Tapatalk
  9. Replies
    22
    Views
    2,004

    You could probably ditch the round ram BP. ...

    You could probably ditch the round ram BP.



    Sent from my iPhone using Tapatalk
  10. Replies
    22
    Views
    2,004

    Deckel FP3 universal

    Correct, my error. I knew there was an L involved. Thanks.


    Sent from my iPhone using Tapatalk
  11. Replies
    22
    Views
    2,004

    Well, thatís an LK. Different breed of cat. Nice...

    Well, thatís an LK. Different breed of cat. Nice machine though.


    Sent from my iPhone using Tapatalk
  12. Replies
    6,662
    Views
    155,514

    This from Wikipedia on Ursulaís ancesters: ...

    This from Wikipedia on Ursulaís ancesters:

    ďThe Ladson family were large plantation owners and her ancestor James H. Ladson owned over 200 slaves by the time slavery in the United States was...
  13. Replies
    16
    Views
    1,816

    Isnít H-S Spanish? This guy says the machine is...

    Isnít H-S Spanish? This guy says the machine is Swiss.


    Sent from my iPhone using Tapatalk
  14. Replies
    6,662
    Views
    155,514

    How would term limits attract better people to...

    How would term limits attract better people to the job?



    Sent from my iPhone using Tapatalk
  15. Looks like a very fair deal to me. I think you...

    Looks like a very fair deal to me. I think you should stop yakking and go get it.


    Sent from my iPhone using Tapatalk
  16. Replies
    6
    Views
    1,324

    I have this Lisle 91000 available. Bought new by...

    I have this Lisle 91000 available. Bought new by my neighbor, never used. $550 plus shipping from 53186.
    https://uploads.tapatalk-cdn.com/20211128/f5401bbe27407a96837a9b98bfdded57.jpg...
  17. Replies
    9
    Views
    1,316

    I took another look at the fuel solenoid. Cleaned...

    I took another look at the fuel solenoid. Cleaned the connectors verified the ground went through the distributor and ignition coil replaced some wires and cleaned contacts. Runs fantastic now....
  18. Replies
    9
    Views
    1,316

    Toyota Forklift Propane Problem

    About 1980 Toyota forklift with 4 cylinder motor. Been on propane all itís life. Usually reliable but now wonít run consistently. Starts and runs a few seconds, maybe up to 10 seconds, then quits....
  19. Replies
    38
    Views
    4,025

    Got the last item boxed and ready to ship. Have...

    Got the last item boxed and ready to ship. Have not heard back from colt45 on the pulley and 220swifts pm box is full so donít know if he still wants the dial. There are still some good parts, the...
  20. Replies
    23
    Views
    2,668

    Iím no expert for sure but it seems obvious that...

    Iím no expert for sure but it seems obvious that if you are going to cut a different number of teeth into the same diameter shaft you will need a different hob. One hob will cut one tooth shape....
  21. I worked for morons way too long thinking they...

    I worked for morons way too long thinking they actually knew what they were doing.
  22. Replies
    28
    Views
    1,859

    Light elements, boron, carbon, lithium, etc donít...

    Light elements, boron, carbon, lithium, etc donít emit x-rays. Not efficiently anyway. So XRF is not reliable for light elements.


    Sent from my iPhone using Tapatalk
  23. Replies
    11
    Views
    1,138

    And congrats on a great machine! Sent from...

    And congrats on a great machine!


    Sent from my iPhone using Tapatalk
  24. Replies
    11
    Views
    1,138

    I have the same table on my FP2. I have the...

    I have the same table on my FP2. I have the encoder and cable but donít have the display box thatís sitting on top the TNC box. When you get around to it what is the model number for that box....
  25. Replies
    12
    Views
    1,355

    These donít have feet like the one in the opís...

    These donít have feet like the one in the opís photo.
    https://uploads.tapatalk-cdn.com/20211103/f6d8e1237af26526af7858509101b503.jpg


    Sent from my iPhone using Tapatalk
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4