Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: triumph406

Page 1 of 60 1 2 3 4

Search: Search took 0.02 seconds; generated 20 minute(s) ago.

  1. Replies
    14
    Views
    426

    If that was the case you wouldn't be asking...

    If that was the case you wouldn't be asking questions here.
  2. Replies
    503
    Views
    31,335

    Maybe the three you mentioned (and maybe others)...

    Maybe the three you mentioned (and maybe others) come configured from the factory where they don’t need to be updated.

    Is every brother owner getting this USB stick free, or do they have to...
  3. Replies
    25
    Views
    983

    I don't think so. It's possible they could have...

    I don't think so. It's possible they could have held Europe under a different leader. But not Hitler. At some point in the war the allies shelved any notion os assasinating Hitler. They figured the...
  4. Replies
    6,044
    Views
    178,112

    The Germans won't put up with the Tesla bullshit....

    The Germans won't put up with the Tesla bullshit. Tesla (and SpaceX) has a very poor reputation as employers, only matched by the disdain a lot of suppliers feel for them.

    If they think they can...
  5. Replies
    503
    Views
    31,335

    You made the right choice. The lack of full...

    You made the right choice. The lack of full enclosure is also a downside to the RMC55.
  6. Replies
    503
    Views
    31,335

    I have a Makino RMC55 that has to have the tools...

    I have a Makino RMC55 that has to have the tools changed manually, complete and utter pita!

    When I got a Fadal and watched the ATC spinning around and tool changes of maybe 20 seconds tool to tool...
  7. yes that hose, it can get damaged if your not...

    yes that hose, it can get damaged if your not carefull cleaning out chips. After 25 years it's probably not as flexible as it once was

    When I looked at one of the fadals I have there was oil on...
  8. My pump has the plunger you can pull up to pump...

    My pump has the plunger you can pull up to pump lube.

    the one in the picture is a lot different to mine
  9. The Turcite in the picture looked dry. I'd check...

    The Turcite in the picture looked dry. I'd check that all the mettering valves are working. If you take the oil lines downstream of the metering valve off the metering unit, then manually actuate the...
  10. I've been using the Fanuc 15m post in an old...

    I've been using the Fanuc 15m post in an old version of surfcam, after editing the post format it works flawlessly. I run Format 2
  11. I'm still using NX2, and it does everything I...

    I'm still using NX2, and it does everything I need it to do
  12. The tachometer brushes on the DC servos will...

    The tachometer brushes on the DC servos will cause more issues than the motor brushses. If the servo jerks backwards and forwards ove rshort distances, more than likely it's the tachometer brushes,...
  13. Have you tried these guys? Accurate Steel...

    Have you tried these guys?

    Accurate Steel Treating, Accurate Ion Technologies
    10008 Miller Way, South Gate, CA 90280
    E-mail: [email protected]
    Accurate Steel Treating | Home
  14. Replies
    503
    Views
    31,335

    I worked in a place in Portsmouth UK in 1982 that...

    I worked in a place in Portsmouth UK in 1982 that made CO2 scrubbers for nuclear submarines. Regardless of the material certs that came with the mat'l, every piece of material that came in,...
  15. Replies
    84
    Views
    6,194

    You can rent a building probably without a permit...

    You can rent a building probably without a permit of any sort, I've never been asked for one.

    But I think your not going to get the permit of occupancy until you have done the fictitious name...
  16. Replies
    503
    Views
    31,335

    Bob, both the stress on the pull stud and the...

    Bob, both the stress on the pull stud and the tensile strength of the pull stud are both expressed as psi. Therefore you can divide one by the other.
  17. Replies
    503
    Views
    31,335

    truth be told we'll probably never know what...

    truth be told we'll probably never know what happened, if it wasn't the OP at the machine but an operator, most operators won't fess upto making a mistake that would trash a spindle.

    It's a bit...
  18. Replies
    503
    Views
    31,335

    The neck on the BT30 pull stud is 7mm dia =...

    The neck on the BT30 pull stud is 7mm dia = .2755"

    area = (.2755/2)*(.2755/2) * pi = .0596in^2

    tensile stress = Force /area

    If BT30 retention force is 700#

    tensile stress = 700# /...
  19. Replies
    124
    Views
    5,430

    I'm really late with some parts for a good...

    I'm really late with some parts for a good customer, might have to use the I got the flu excuse, of course if he believes me, and then I get the flu I'll be in a pickle.
  20. I've machined pattern welded steel or Damascus as...

    I've machined pattern welded steel or Damascus as you call it.

    I roughed the shape using a 3/8 flatbottom, and finished the blade with a 3/8 ball.

    The big problem is the amount it moves when...
  21. Replies
    503
    Views
    31,335

    Something you armchair metallurgists etc seem to...

    Something you armchair metallurgists etc seem to miss is that the stress on the pull stud is 11'733psi for a retention force of 700#

    So if a pull stud was a thru hardening steel with a strength...
  22. Replies
    503
    Views
    31,335

    I've been running the same long skinny pull-studs...

    I've been running the same long skinny pull-studs on my Makino since 1995. I have close to 2000# retention force.

    Probably should replace them I guess. I'll get some more from Mari-tool nexr time...
  23. If you buy a brand new Ripper mill body and...

    If you buy a brand new Ripper mill body and inserts it's going to be cheaper than the used bodies and the inserts your trying to sell.

    Plus for the toolholders without screws, if you can't supply...
  24. Replies
    503
    Views
    31,335

    The short Pull stud looks suspiciously like a...

    The short Pull stud looks suspiciously like a Fadal pull stud, the longer one looks like a pull stud I use on my Makino.

    There is a big difference in the spindle tapers between my Fadals and my...
  25. Replies
    6,044
    Views
    178,112

    There was also plenty of American interference in...

    There was also plenty of American interference in the Brexit campaign.

    The Mercers who bank roll Breitbart, (and who used to bankroll Steve Bannon) put a lot of money into the leave campaign.
    ...
Results 1 to 25 of 1493
Page 1 of 60 1 2 3 4