Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: jhruska

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Basic educational: $5,700 Leading Edge...

    Basic educational:
    $5,700 Leading Edge Industrial Shop: HX8610 Vertical Machining Center
    $5,000 Leading Edge Industrial Shop: HX8610 Vertical Machining Center
  2. Replies
    2
    Views
    638

    Here is a photo showing simple setup tooling for...

    Here is a photo showing simple setup tooling for a planer that has table holes like yours.
    Made from hot rolled square stock. The cup point square head screws are hardened.
    Old center drills or...
  3. Replies
    2
    Views
    638

    Nice work! I flipped your pics:D 302015302016...

    Nice work!
    I flipped your pics:D
    302015302016
    John
  4. Congratulations! This is a very capable mill and...

    Congratulations!
    This is a very capable mill and I have machine envy :D
    Regards, John
  5. The bevel gear problem is a surprise as that is...

    The bevel gear problem is a surprise as that is reasonably indestructible. Perhaps there was feed engagement at high rpm?
    I worked on a CNC Webb mill that is essentially a beefed up Bridgeport...
  6. The top end has to come off, motor, housing, ect....

    The top end has to come off, motor, housing, ect.
    Run head to lowest rpm.
    Lock-out and tag the electric.
    Separate forward-reverse switch from housing.
    Remove motor, invert it and stand it on the...
  7. PM sent, Regards John

    PM sent, Regards John
  8. Replies
    1
    Views
    260

    Yes, the chip load per tooth for a machine reamer...

    Yes, the chip load per tooth for a machine reamer using the feeds will produce a nice finish.
    John
  9. Plan B, Aetna thrust bearings come up for sale on...

    Plan B, Aetna thrust bearings come up for sale on ebay for small money.
    I like the E-series with the enclosed housing and oil hole.
    The E-series has two bore dimensions. The small dimension locates...
  10. Replies
    25
    Views
    2,825

    The link to Gahr: Gahr Machine Company -...

    The link to Gahr:

    Gahr Machine Company - Warner & Swasey Parts, Tools, Manuals

    Regards, John
  11. .......and center the table, drop the knee.

    .......and center the table, drop the knee.
  12. 1.377 Just measure the shaft on the machine. I...

    1.377
    Just measure the shaft on the machine.
    I quit using the mandrel and never looked back.
    Direct fit-epoxy cure on the spindle or motor shaft is a better fit then using the mandrel
    and the...
  13. The timing belt does not need replacement as...

    The timing belt does not need replacement as often as the Vari-disc drive belt. Inspect all the pads for tears or separation. If present replace.
    The 1&1/2 hp and 2 hp take different timing belts....
  14. G-ManBart Yes replace the belt and while things...

    G-ManBart
    Yes replace the belt and while things are apart pull the front vari-disc and inspect the bushings and key.
    The Goodyear belt runs quiet for a home shop as it has a softer rubber compound...
  15. Single of double throw? Push button switches...

    Single of double throw?
    Push button switches that mount right to the enclosure without the outboard support are common.
    John
  16. Replies
    1
    Views
    602

    Arrived today nicely packaged. Thanks! John

    Arrived today nicely packaged.
    Thanks!
    John
  17. Replies
    9
    Views
    629

    A few more: 297309297310297311297312 This...

    A few more:
    297309297310297311297312

    This vertical boring mill is similar to one I worked on as a helper in 1979. At that time one of the two new Bethlehem blast furnaces in Burns Harbor, Indiana...
  18. Replies
    9
    Views
    629

    "If ever there was a wiz there was........"from...

    "If ever there was a wiz there was........"from L. Frank Baum.
    Not I but here are three of the first images plus images of "The White City" Colombian Exposition, the place where it happened.
    One...
  19. Replies
    7
    Views
    2,777

    Bought some parts from Ron Grundy for my...

    Bought some parts from Ron Grundy for my Milwaukee 2K.
    Thanks, hard to find parts arrived exceeding expectations :D
    John
  20. Replies
    6
    Views
    698

    The height of the inner and outer races of the...

    The height of the inner and outer races of the replacement bearings should be the same. Duplex bearings (DUL) will have a reduced height of one of the races. That will be the pre-load applied if the...
  21. Not in Seattle, lathe is located West of Lakeland...

    Not in Seattle, lathe is located West of Lakeland where our daughter lives and they are healthy and safe.
    John
  22. Looks like the faceplate can be had for $1.00....

    Looks like the faceplate can be had for $1.00.
    https://offerup.com/item/detail/809607454/
    293648
    John
  23. Replies
    5
    Views
    785

    Relevant images: 293489293490293491293492293493...

    Relevant images:
    293489293490293491293492293493
    John
  24. It's the LeBlond-a-saurus Rex :D

    It's the LeBlond-a-saurus Rex :D
  25. Sheldon 10" & 11" lathes take a stubby MT-5....

    Sheldon 10" & 11" lathes take a stubby MT-5.
    Large dia. about 1.625"
    John
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4