Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Hbjj

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    19
    Views
    1,177

    Thanks for the photos Now you got me thinking...

    Thanks for the photos
    Now you got me thinking 269481
  2. Replies
    19
    Views
    1,177

    Cool Any photos of the tooling and machine?

    Cool
    Any photos of the tooling and machine?
  3. Replies
    8
    Views
    822

    Yes a small coil spring above the clapper pivot...

    Yes a small coil spring above the clapper pivot pin
    But if I were making a new tool I would probably move it under the pin and pull the clapper back instead of pushing
  4. Replies
    8
    Views
    822

    .750/6.5 inches deep 4140 QT Bar is bolted in...

    .750/6.5 inches deep 4140 QT
    Bar is bolted in place of the clapper and there is a small clapper built in to the end of the bar
    All cutting is straight down only a spring cut across the bottom ...
  5. 267927 7"od commercial fishing boat propeller...

    267927
    7"od commercial fishing boat propeller shaft bearing
    267929
    Follower rest and new cross slide lead screw 267931
    267932
    Daughter's lt80 cylinder
  6. That is awesome! I need one Would love to get...

    That is awesome!
    I need one
    Would love to get out of the stone age 267266
  7. Thread: ETD150 Steel

    by Hbjj
    Replies
    11
    Views
    1,846

    I like etd 150 it machines nice but it WILL move...

    I like etd 150 it machines nice but it WILL move as you work it
    I recently made a new cross slide lead screw out of it and it moved about .030 after threading 265623
    I would not use it for...
  8. Replies
    25
    Views
    2,488

    Yup and 12 point sockets work to but..

    Yup and 12 point sockets work to but..
  9. Replies
    25
    Views
    2,488

    Old sawmill/millwrigh trick is to press a nylock...

    Old sawmill/millwrigh trick is to press a nylock on to the back of a tap and drive it with a air impact gun
    Git er done!
  10. Google search (moody method surface plate...

    Google search (moody method surface plate calibration)
  11. Perhaps you could use this technology instead of...

    Perhaps you could use this technology instead of scraping
    ...
  12. Could this machine be applied welding? I had a...

    Could this machine be applied welding?
    I had a heck of a time getting at a forklift the other day
    It would have shure been nice to position it at a more convenient angle/elevation ...
  13. Replies
    36
    Views
    5,507

    I'm shure for a real shop 785$ is small money ...

    I'm shure for a real shop 785$ is small money

    But this was for my plate at home
    no way can I justify that

    So I figured out a way to do it myself talk about not knowing what you're doing...
  14. Replies
    36
    Views
    5,507

    Found it 259925

    Found it

    259925
  15. Replies
    36
    Views
    5,507

    I had a quote a while ago to lap my 2x3 from b to...

    I had a quote a while ago to lap my 2x3 from b to a it was about 800$ IIRC they were 175$ an hour
  16. Thread: Line boring

    by Hbjj
    Replies
    37
    Views
    29,513

    Another forklift but this time I'm working on the...

    Another forklift but this time I'm working on the main frame also
    259235259236259237259238259239
  17. Replies
    6
    Views
    1,068

    Is it possible the screws are there to adjust the...

    Is it possible the screws are there to adjust the lash ?
    Or is there some other way
  18. Replies
    4
    Views
    1,129

    It looks like the lathe is not installed or level...

    It looks like the lathe is not installed or level so that will be the first thing to do

    You need to map out the wear

    A kingway type tool is what I would want

    Good luck
  19. Replies
    17
    Views
    2,546

    I assume by lapping on your surface plate you are...

    I assume by lapping on your surface plate you are talking about using sandpaper taped or glued down
    I do this on occasion but the paper will form sort of a wave in front as you push your parts...
  20. Replies
    3
    Views
    1,399

    These are from a doall bandsaw counter weight I...

    These are from a doall bandsaw counter weight
    I would sell the solid back one it doesn't hinge well now so consider it just rough scraped
    I have no need for two!
    252717252718252719
  21. I think the test should be similar to what I've...

    I think the test should be similar to what I've already done

    It should be a straight edge and measurements should be taken by reading the print

    I guess the difference would be that it is a...
  22. I'm still curious about the ringing question also...

    I'm still curious about the ringing question also
    I would donate machine/scraping time to a good test
  23. 251382 Checked this again and it appears to have...

    251382
    Checked this again and it appears to have moved back even more while sitting in my tool box over these months.
  24. Thread: Fly Cutting

    by Hbjj
    Replies
    29
    Views
    4,412

    Grinding your own tools is a machinist right of...

    Grinding your own tools is a machinist right of passage
    So learn that
    But carbide is so much faster
    My current small insert and a couple of tools I made two use the (other) corners

    248654
  25. Thread: Slip roller crown

    by Hbjj
    Replies
    34
    Views
    2,044

    It's standard practice to add a shim of some sort...

    It's standard practice to add a shim of some sort to many/most forming jobs.
    rolls and brakes
    Anyone who says they dont is not being honest or they don't know what they're doing
Results 1 to 25 of 287
Page 1 of 12 1 2 3 4