Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Fish On

Search: Search took 0.00 seconds.

  1. Replies
    72
    Views
    5,999

    Phase 1 enviro came back clean, and survey...

    Phase 1 enviro came back clean, and survey (boundary only, decided against topo) showed pretty much what we expected it to, so I guess we're about to be off to the races.
  2. Replies
    72
    Views
    5,999

    Near as I can tell, I can do most anything to it...

    Near as I can tell, I can do most anything to it that meets building codes/hurricane wind rating. Zoning limitations, if it were zoned, have to do with building use, setbacks, required number of...
  3. Replies
    72
    Views
    5,999

    What is the consensus on topo survey vs just...

    What is the consensus on topo survey vs just boundary survey?

    I was originally planning on the topo survey to alleviate the issue that Mike1974 mentioned about an X not being a complete X. ...
  4. Replies
    72
    Views
    5,999

    Well, I have a contract on the piece of land,...

    Well, I have a contract on the piece of land, pending environmental and survey, so it seems this is the route I'm going to go.


    I'm awaiting a recommendation for the Phase 1 environmental...
  5. Replies
    72
    Views
    5,999

    I know, but the next rack over from the hold...

    I know, but the next rack over from the hold rolled rounds says "cold rolled rounds". Not cold drawn rounds.


    It's just gotta be lazy nomenclature. Plate comes in hot rolled and cold rolled. ...
  6. Replies
    72
    Views
    5,999

    Same. Not that I buy much steel at all, but my...

    Same. Not that I buy much steel at all, but my suppliers generally have it listed as hot roll round, or cold roll round. Got a flyer pinned to the bulletin board a steel distributor recently left...
  7. Replies
    72
    Views
    5,999

    Ah, gotcha. I'm in fabrication, not machining,...

    Ah, gotcha. I'm in fabrication, not machining, and virtually 100% aluminum at that, so CDS isn't in my daily vocabulary. My stuff comes in the form of 5x10 sheets, which is why I want at least 12'...
  8. Replies
    72
    Views
    5,999

    I like the idea of the shop at the house from a...

    I like the idea of the shop at the house from a here and now standpoint - WAY less money spent now, and somewhat less monthly operating costs, but you're exactly right, in the long run, the...
  9. Replies
    72
    Views
    5,999

    What is CDS?

    What is CDS?
  10. Replies
    72
    Views
    5,999

    Yes, no question. I've been without it for the...

    Yes, no question. I've been without it for the past 8 years here in Ga. Always said as soon as I owned a place, I'm putting AC in. Good point on doors location. Hadn't considered that, but my two...
  11. Replies
    72
    Views
    5,999

    Sewer is on the lot. It's a pressurized line, so...

    Sewer is on the lot. It's a pressurized line, so I'll need a pump on my end, but I do have a handle on the cost for that, plus the hookup fee. To be thorough, I may still research septic...
  12. Replies
    72
    Views
    5,999

    It might be better. I'll have to see how it lays...

    It might be better. I'll have to see how it lays on the lot - lot is long and narrow.

    Initially, which is probably the bigger concern, the extra cost of the trusses would probably somewhat wash...
  13. Replies
    72
    Views
    5,999

    Best I can tell, it's in zone X, which appears to...

    Best I can tell, it's in zone X, which appears to be above the 500 year flood, so we should be good there.
  14. Replies
    72
    Views
    5,999

    Let's not get too hung up on the building size...

    Let's not get too hung up on the building size and cranes. My current shop is a 30x60, and while it has pretty much everything in an awkward spot, which has forced a less than ideal interior layout...
  15. Replies
    72
    Views
    5,999

    Building a new shop on commercial land

    A couple months back, I inquired about moving my shop from a leased commercial property to a home property while moving to a new state. Lots of good feedback there. During that time, I was second...
Results 1 to 15 of 15