Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: johnoder

Page 1 of 60 1 2 3 4

Search: Search took 0.15 seconds.

  1. Replies
    2
    Views
    152

    Email sent on the works

    Email sent on the works
  2. Replies
    9
    Views
    242

    The B&S work spindle here can be locked (like...

    The B&S work spindle here can be locked (like grinding between centers - when only the dog driver rotates) or rotating like for spinning something in a chuck - a common accessory for a Universal
    ...
  3. Replies
    9
    Views
    242

    Cincy is Universal - you can see the swivel at...

    Cincy is Universal - you can see the swivel at bottom on work head. Smaller wheel typical on Universal compared to "plain". My 14 X 60 B&S only has 14" X 1 1/2" wide

    These are incidentally much...
  4. Replies
    10
    Views
    323

    Dang! That's a good looking SR! :D

    Dang! That's a good looking SR!
    :D
  5. Replies
    9
    Views
    242

    Indeed - and my 1947 B&S #4 does also Here is...

    Indeed - and my 1947 B&S #4 does also

    Here is Norton scan from WW2

    320830

    Could maybe pry up on a wood block under wheel to check wheel side bearing for sloppiness - there should be next to...
  6. Replies
    19
    Views
    941

    The only pub I know of even close is the one you...

    The only pub I know of even close is the one you refer to

    SB made lathes, not piles of paper about "rebuilding" them

    Its a series "O", a very simple lathe they stopped making over 80 years back...
  7. Replies
    10
    Views
    323

    Shows the drive gear box that goes on end of...

    Shows the drive gear box that goes on end of table

    320810320811
  8. Replies
    2
    Views
    102

    I'll suppose surface grinder and that makes it...

    I'll suppose surface grinder and that makes it 1947

    Does your friend still have his giant Le Blond?

    F/S Big LeBlonde Lathe

    have fun
  9. Plus one here - don't worry about inside weld -...

    Plus one here - don't worry about inside weld - find out where it is and mill a groove for it in the insert.
  10. I used TWO dogs - one on TS quill with the vee...

    I used TWO dogs - one on TS quill with the vee typical of grinding dogs and one plain bent tail dog on the drill. The set screw of the grinding dog sticks in the key way on bottom of TS quill ( not...
  11. Replies
    1
    Views
    186

    Photos may help Here is one of the how-to...

    Photos may help

    Here is one of the how-to threads

    https://www.practicalmachinist.com/vb/south-bend-lathes/posting-pictures-south-bend-forum-372508/?highlight=photos

    have fun
  12. The point is is that you have an interesting pile...

    The point is is that you have an interesting pile of iron, with a strong likelihood you will never use - unless drilling and tapping (or otherwise machining) for whatever YOU want to bolt on

    :D
  13. And several appear to have in their resumes...

    And several appear to have in their resumes mounting of various spindle tooling - like custom fixtures
  14. Thread: Hendey 14x6

    by johnoder
    Replies
    88
    Views
    5,547

    The old pesky word Often as confidence...

    The old pesky word



    Often as confidence builds and skills develop it will be more reasonable to DISCARD "find" and substitute MAKE

    :D
  15. Thread: Hendey 14x6

    by johnoder
    Replies
    88
    Views
    5,547

    Early twenties catalog says #2 for 12, 14 and 16"...

    Early twenties catalog says #2 for 12, 14 and 16" - they all have a bush - the outside of which fits in the spindle and the inside of which fits the #2 collet set. May be differing in detail for...
  16. 1958 per serial book - its referred to as the...

    1958 per serial book - its referred to as the "old" model
  17. Replies
    25
    Views
    1,329

    Here is my old transcription of what was written...

    Here is my old transcription of what was written about "semi steel" in a book published in 1917. I'd apologize for the language but its his, not mine

    Book is Principles of Iron Founding and what...
  18. The "allen" set screws push on "scalloped" or...

    The "allen" set screws push on "scalloped" or beveled plugs to grip the bar
  19. Two different B&S 9 tapers in MHB - probably need...

    Two different B&S 9 tapers in MHB - probably need to concentrate on the Milling Machine version :)

    Standard Tapers

    Have fun
  20. B&S called them Universal Back Rests - finely...

    B&S called them Universal Back Rests - finely adjustable to just overcome "push off" on long skinny work pieces
  21. My same year (1947) No. 4 has been a great...

    My same year (1947) No. 4 has been a great grinder. These are mechanical - no hydraulics

    320664320665320666320667
  22. Replies
    35
    Views
    1,400

    Here is a non vary speed 32 speed one - I suppose...

    Here is a non vary speed 32 speed one - I suppose from mid fifties

    320655
  23. Replies
    40
    Views
    2,817

    I think lube specs are in the K&T part of Vintage...

    I think lube specs are in the K&T part of Vintage Machinery. If like the smaller mills - DTE Heavy Medium in both column and knee
  24. Ahhhh - an opportunity to post the photos of the...

    Ahhhh - an opportunity to post the photos of the one I looked at here in Houston with the "bucket of rocks" sounding head stock

    320646320647320648320649320650
  25. The 2 TPI QC gear box was gone in the late...

    The 2 TPI QC gear box was gone in the late thirties. All later single tumbler QC boxes were 4 TPI

    My August '46 full line catalog 100-F still has the single tumbler set up

    Here is the last of...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4