Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: skipd1

Page 1 of 10 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    334

    Thanks I'll talk to you about it later Skipd1

    Thanks I'll talk to you about it later

    Skipd1
  2. Replies
    5
    Views
    334

    That's not what I was describing, I'm talking...

    That's not what I was describing, I'm talking about the micrometer collar on the handle.
  3. Replies
    5
    Views
    334

    What's missing on this Hendey compound

    Does anyone know what's missing on my Hendey 12x30 compound to lock the adjusting ring. Now all it does is spin around and won't stay in position? On the PDF parts breakdown it shows a small...
  4. Replies
    4
    Views
    397

    The next project is to remove clean and strip the...

    The next project is to remove clean and strip the paint off the rest of the rear covers surrounding the drive pully and clutch. This is a messy and time consuming job. All the covers came off without...
  5. Replies
    4
    Views
    397

    I ran it when I evaluated it at time of purchase...

    I ran it when I evaluated it at time of purchase and it all seemed to be really in good condition. My issue is that I not have it temporarily in my garage for the refurb and to get in my shop is a...
  6. Replies
    4
    Views
    397

    12x30 Hendey 18 speed Project (with pics)

    I have recently picked up a new to me 1938 Hendey 12x30 18 speed gear head lathe. I have been posting my progress on another forum but not getting much feedback so I'm going to try here.
    340530
    My...
  7. Thread: Motor Info

    by skipd1
    Replies
    8
    Views
    813

    Thanks, sorry about the pic being upside down

    Thanks, sorry about the pic being upside down
  8. Thread: Motor Info

    by skipd1
    Replies
    8
    Views
    813

    Here are some pics of the motor and the motor...

    Here are some pics of the motor and the motor plate. Its currently wired for 240v 3 phase and it runs extremely quiet for being 84 years old

    338134
    338135
  9. Thread: Motor Info

    by skipd1
    Replies
    8
    Views
    813

    Thanks everyone. I will take some pics later. It...

    Thanks everyone. I will take some pics later. It is a 3 phase motor and has both forward and reverse switches on the front. I will try to get a pic of the magnetic starter also
  10. Thread: Motor Info

    by skipd1
    Replies
    8
    Views
    813

    Motor Info

    338042
    This is a Westinghouse 3 hp motor out of a 1938 Hendey lathe. Does anyone have any info on this motor, like does it have brushes or not?
  11. Replies
    8
    Views
    881

    Thanks skipd1

    Thanks

    skipd1
  12. Replies
    5
    Views
    708

    Thanks skipd1

    Thanks

    skipd1
  13. Replies
    8
    Views
    881

    Lathe Chuck and tool post sizing

    I have a recent acquisition of a 1938 Hendey 12x30 gearhead lathe and I want to correctly size the chuck and quick change tool post for it. This machine is an RS or raised swing model and its maximum...
  14. Replies
    5
    Views
    708

    Lathe Chuck and tool post sizing

    I have a recent acquisition of a 1938 Hendey 12x30 gearhead lathe and I want to correctly size the chuck and quick change tool post for it. This machine is an RS or raised swing model and its maximum...
  15. Replies
    2
    Views
    616

    Thanks I have quite extensively gone over this...

    Thanks
    I have quite extensively gone over this thread and it's quite helpfull

    Skipd1
  16. Replies
    2
    Views
    616

    Hendey 12x30 gearhead lathe home

    After almost 2 months of negotiating and evaluating I finally got the Hendey 12x30 lathe home and temporarily in my garage for initial cleanup and some refurbishment. I plan to drain and flush the...
  17. Thread: Hendey Lathe

    by skipd1
    Replies
    11
    Views
    1,946

    Thanks for all the great input skip

    Thanks for all the great input

    skip
  18. Because I was hoping to get the attention of...

    Because I was hoping to get the attention of Hendeyman as I read he watches this forum

    Skip
  19. Yes you are correct serial #29888 was built in...

    Yes you are correct serial #29888 was built in 1938 and has a US Navy tag on it. Thanks

    skip
  20. New to me 1930 Hendey 12x30 18 speed gearhead lathe

    I recently pulled the trigger and purchased a 1930 Hendey 12x30 gear head lathe. The lathe is labeled as a 12" swing, but it should handle more. It came only with a 8" 3 jaw chuck, so I need a 4 jaw,...
  21. Mine has a D1-6 spindle Thanks Skipd1

    Mine has a D1-6 spindle
    Thanks
    Skipd1
  22. Replies
    4
    Views
    569

    Hendey 12x30 gearhead lathe steady rest

    I am looking for a steady rest that fits a 12" Hendey lathe or at least some specs to build one by?
    Thanks
    skipd1
  23. Newly acquired 1930 Hendey 12x30 18speed Gearhead lathe

    I recently pulled the trigger and purchased a 1930 Hendey 12x30 gear head lathe. The lathe is labeled as a 12" swing, but it will handle 14 inches. It came only with a 8" 3 jaw chuck, so I need a 4...
  24. Thread: Hendey Lathe

    by skipd1
    Replies
    11
    Views
    1,946

    My only concern is if the machine is in good...

    My only concern is if the machine is in good condition will it do accurate work on small diameter projects or is it going to be just a beast to carve off material?
    I have an old 1930 South Bend...
  25. Thread: Hendey Lathe

    by skipd1
    Replies
    11
    Views
    1,946

    Well thanks for all the great comments, there...

    Well thanks for all the great comments, there greatly appreciated.
    It looks like I am going to get to inspect and possibly purchase the 18 speed 12x30 Hendey I have referred to sometime around...
Results 1 to 25 of 226
Page 1 of 10 1 2 3 4