Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: CarbideBob

Page 1 of 60 1 2 3 4

Search: Search took 0.06 seconds.

  1. On caveat when programing this small of an...

    On caveat when programing this small of an entrance rad.
    If the OD was not cut by the same tool and that OD is say .002 oversize or undersized you end with rather poopy blend be it a notch in the...
  2. Replies
    44
    Views
    3,764

    It is the world of plastic sheet that makes this...

    It is the world of plastic sheet that makes this a mess.
  3. This an often repeated lore or tall tale in the...

    This an often repeated lore or tall tale in the machining world.

    No matter how much the engineer a dick and hard to talk to most would take the time to explain and not waste time and money.
    If...
  4. Replies
    3,643
    Views
    102,546

    I got vaccinated for polio and smallpox. Seemed...

    I got vaccinated for polio and smallpox.
    Seemed that this helped.
    I do not think my parents saw it as a way to control the masses or the world.
    Perhaps if they did these would still be running...
  5. Replies
    201
    Views
    10,801

    Is any repair as good as new? Sometimes there...

    Is any repair as good as new?
    Sometimes there are repairs that fix design problems so maybe better.
    That is not common.
    An auto engine will go 250,000 miles out of the factory. Ask a rebuilder for...
  6. Replies
    29
    Views
    1,882

    Cleaning optics in this range is an art in...

    Cleaning optics in this range is an art in itself.
    Cotton swaps are themselves abrasive so be very gentle and of course no dirt pickup side involved.
    Front surface mirrors, do not touch. spray...
  7. Replies
    13
    Views
    967

    Here is off for colors Dark green canvas. Not...

    Here is off for colors
    Dark green canvas.
    Not only blocks all light but people do not spend time watching the welders do their work.
    Weld area is sort of a magnet to people who want to watch this...
  8. Replies
    201
    Views
    10,801

    Does this product have a big problem with this?...

    Does this product have a big problem with this?
    Is this a design flaw or just overrun chains?

    I do not think the OP's request was out of the ballpark.
    And then questions or maybe a bit of...
  9. Replies
    51
    Views
    2,545

    Ouch, as much as I hate this method it often...

    Ouch, as much as I hate this method it often works.
    Why, Because the wheel is not hub centered and some up/down shift breaks it free. It is not just the hub the wheel attaches itself to.
    In a truly...
  10. Replies
    201
    Views
    10,801

    Most of the case repairs I do are not chain...

    Most of the case repairs I do are not chain throws.
    More of two stokes eating pistons.
    Bob
  11. Replies
    51
    Views
    2,545

    I think many OEMs that appears hub centric are...

    I think many OEMs that appears hub centric are not.
    One could get out the the bore gauges and mics to check on new. I do not think these are one thou fits.
    It is close for ease and speed of...
  12. Replies
    201
    Views
    10,801

    For sure if deep in the forest and hard trails...

    For sure if deep in the forest and hard trails home.
    Sleds or four wheelers are so much easier.
    Now this that this thread has gone a tad off the track it is a bit more friendly.
    Bob
  13. Replies
    51
    Views
    2,545

    Confused here. I thought centering off the hub...

    Confused here. I thought centering off the hub and wheel hole went away a fair bit back.
    Bob
  14. Replies
    201
    Views
    10,801

    I've also had very bad luck trying to tow a bike...

    I've also had very bad luck trying to tow a bike behind a car, four wheeler or other bike.
    I would wrap the rope or strap over itself and not tie it but hold one end to the bar in my hand. That way...
  15. Replies
    51
    Views
    2,545

    In the way back days no mills had DROs. You also...

    In the way back days no mills had DROs.
    You also learned to eliminate lash and approach all numbers on the dials from the same direction.
    Even a old mill with .050 lash should get you within .003...
  16. Who needs more power and what do the water levels...

    Who needs more power and what do the water levels look like.
  17. I would have to be big big no on this with my...

    I would have to be big big no on this with my limited experience.
    This is insane, Never have seen 100 to 288,000 be off by one count unless mounted badly. This sort of goes with how these things...
  18. Replies
    201
    Views
    10,801

    Bart Markel taught me to run the fireroads and...

    Bart Markel taught me to run the fireroads and will never forget that. He worked at AC for a real job. That my intro as a kid to go faster and lay it out.
    Never ridden with Jay as not a woods guy...
  19. Replies
    201
    Views
    10,801

    Powersports . That is crazy land and hard to...

    Powersports . That is crazy land and hard to understand the function of these peoples brains.
    Put 10,000 Horsepower In A Small Boat and This Is What Happens - YouTube
    Eddie Hill was good on 2...
  20. From your numbers I get that your groove needs to...

    From your numbers I get that your groove needs to look like this below.
    If true , no, can not be done with any FNR tool as clearing the corners impossible as this not a full radius groove.
    If I am...
  21. Time from start of process to end at $60 per...

    Time from start of process to end at $60 per hour. Assume soak time unattended and free.
    Bob
  22. Replies
    201
    Views
    10,801

    Hmm, not the right tab so punishment needed....

    Hmm, not the right tab so punishment needed.
    That would not make us seem arrogant would it?
    Bob
  23. Replies
    201
    Views
    10,801

    Some talk as if this a big business as in 10-20...

    Some talk as if this a big business as in 10-20 cases a day forever.
    On any given Sunday how many 250Rs in use and how many break a case each week?
    I would think this more as a weekend retired...
  24. Replies
    21
    Views
    1,817

    One basic thing with high feed milling cutters....

    One basic thing with high feed milling cutters.
    Go fast or go home.
    They do do like lower or anything like normal feedrates.
    As shown above it is chip thinning to extremes.
    Measuring your cut...
  25. Replies
    13
    Views
    985

    Dad had a way. "If I go out out on the floor I...

    Dad had a way.
    "If I go out out on the floor I want to see nothing but assholes and elbows"
    "You can never be friends with the employees"
    We did not see eye to eye on many things.

    Me, the...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4