Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: johnoder

Page 1 of 60 1 2 3 4

Search: Search took 0.14 seconds.

  1. Replies
    7
    Views
    188

    6K large diameter is 1.160" - considerably...

    6K large diameter is 1.160" - considerably larger than big end of #3 taper
  2. Replies
    10
    Views
    413

    What breaks? Aluminum? Maybe they are clueless...

    What breaks? Aluminum? Maybe they are clueless about so-so and actually strong aluminum - or equally clueless about over a dozen stress riser grooves needing to be just so in design and execution
  3. Likely be helpful to give a clue about metal

    Likely be helpful to give a clue about metal
  4. Replies
    8
    Views
    502

    The one in the 3613 bandsaw was just worn down on...

    The one in the 3613 bandsaw was just worn down on the pulley fit by Bubba not paying attention

    I left the front bearing on - PUT IT IN THE STEADY REST - and turned to clean up true.

    Since that...
  5. Replies
    2
    Views
    208

    On the CW16, I have one position on one shift...

    On the CW16, I have one position on one shift lever that that over shoots pin FIVE-EIGHTS of an inch, so I just drop in a wood wedge (between pin and lever) and never worry about it
  6. Thumbnails are both Patent Head and Cone head 16...

    Thumbnails are both Patent Head and Cone head 16 from 1910 catalog
  7. Replies
    9
    Views
    506

    And in the knee

    And in the knee
  8. Since it seems the rotary switches' wiring has...

    Since it seems the rotary switches' wiring has not been disturbed, it is very likely the contacts are needing some help

    Thumbnail is a giant Westinghouse rotary switch - the heavy copper contacts...
  9. And showing the hidden lock screws back side...

    And showing the hidden lock screws back side interfering with two of four chuck mount holes. The reason for either thickness or larger bolt circle
  10. Replies
    9
    Views
    506

    If you look under Model H (upper left side of...

    If you look under Model H (upper left side of column) you will find a serial stamped into machined cast iron. It will be in one of the following formats -
    X-XXXX or XX-XXXX - all digits
  11. Replies
    9
    Views
    506

    292 line items here you may want to look thru ...

    292 line items here you may want to look thru

    Kearney & Trecker Co. - Publication Reprints | VintageMachinery.org
  12. Replies
    2
    Views
    450

    There were La Point broaching machines at P&WA in...

    There were La Point broaching machines at P&WA in the mid sixties that had a long line of similar cutters bolted on the vertical ram
  13. Has SWASH plate(?s) to turn reciprocation into...

    Has SWASH plate(?s) to turn reciprocation into rotary
  14. Good luck on getting the stator winding out:)

    Good luck on getting the stator winding out:)
  15. Thread: Sidney Lathe,

    by johnoder
    Replies
    44
    Views
    3,520

    Do bear in mind that unless the latest and...

    Do bear in mind that unless the latest and greatest design involving such things as synchronizers you don't switch this around at elevated speeds

    Give it a shot at say 150 RPM. Down (on your 5/8"...
  16. Thread: Sidney Lathe,

    by johnoder
    Replies
    44
    Views
    3,520

    I'd guess some PO protecting his investment from...

    I'd guess some PO protecting his investment from his half wit employees:D
  17. Looks like a useful turret lathe (that is what...

    Looks like a useful turret lathe (that is what the "2" is for) add on - lever operated rotary switch on back - dealing not only with Fwd / Rev, but also two speeds - resulting in a great bundle of...
  18. Depends:D D1-6" pins are on a 5.250 bolt...

    Depends:D

    D1-6" pins are on a 5.250 bolt circle and their lock screws are more or less on the same B.C. meaning any additional bolting on or near that B.C. have to fit between a lock screw and a...
  19. Replies
    1
    Views
    181

    Put it in top gear, engage clutch and turn pulley...

    Put it in top gear, engage clutch and turn pulley enough times to turn table one full turn and do the math for what ever top speed is placarded

    Say it went six turns on pulley for one full turn of...
  20. 12 page brochure from about then can be emailed...

    12 page brochure from about then can be emailed if you want to private message me that address with NORTON in the subject line
  21. Replies
    7
    Views
    349

    Seems to be headed in right direction. The V484...

    Seems to be headed in right direction. The V484 is upper on my 3613-2, and its lower is 1922 V443

    "1922V484" - Google Search
  22. Replies
    10
    Views
    658

    See 18 March 2016 entrees. - Might be of some use...

    See 18 March 2016 entrees. - Might be of some use

    Kearney & Trecker Co. - Publication Reprints | VintageMachinery.org

    ph
  23. Maybe the one? Did not look thru all 1800 plus...

    Maybe the one? Did not look thru all 1800 plus items

    SCHAUBLIN 102 LATHE - tools - by owner - sale
  24. You just switched a pair of digits Ken - 41697...

    You just switched a pair of digits Ken - 41697 says the old email folder. A 20 standard and - quite unusual - a gap bed. Don't know if block was ever out.

    Thumbnails a bit older before the hard...
  25. Replies
    8
    Views
    633

    Amazing - I.B.I. interchange book lists the...

    Amazing - I.B.I. interchange book lists the Timken 8315 under IBI Group 41634.03 and states it is a Double Taper Cone roller with two cups. The two listed interchanges are even more obscure by...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4