Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: hmcbandit

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    4,650

    Hardinge Spindle Drive Fault

    Dumb me,after a number of calls to Hardinge and Fanuc with assurances that the top board on the spindle drive was bad said they have seen it many times with absolutly no chance of it having a blown...
  2. Replies
    3
    Views
    4,650

    Hardinge chnc spindle drive fault alarm

    I saw that web site and seemed little vague, looking to narrow it down a little (machine specific).The original alarm on the screen was 1001 and the spindle unit showed AL 09.Looking for someone that...
  3. Replies
    0
    Views
    1,382

    Spindle drive alarm

    I can't get my chnc1 out of e-stop. It has a fanuc0t and I get a spindle drive fault alarm and I opened the cabinet and it showed AL 09.The two fans on the bottom of the spindle drive are...
  4. Replies
    3
    Views
    4,650

    Hardinge chnc spindle drive fault

    I can't get my chnc1 out of e-stop. It has a fanuc0t and I get a spindle drive fault alarm and I opened the cabinet and it showed AL 09.The two fans on the bottom of the spindle drive are...
  5. Replies
    1
    Views
    1,784

    Dyna-Myte 4400 X axxis motor

    I'm looking for the part number and model number and manufacturer of the X axxis motor on a Dyna-myte 4400 milling machine with tool changer.Hope to buy one off ebay and not have to deal with...
  6. Replies
    2
    Views
    1,530

    Hardinge HC speed control problem

    I recently picked up a used Hardinge Chucker on ebay, the owner said it ran good but when I picked it up it was disconnected and on a skid.Long story short the rpm speed control does not work(the...
  7. Replies
    4
    Views
    3,464

    Hardinge CHNC turret problem

    Rust Rust and more Rust,to much moisture in the air. Disassembled the turret and it was loaded with rust (need an air dryer),cleaned every thing and replaced the MAC Valve and was able to properly...
  8. Replies
    4
    Views
    3,464

    Hardinge Turret Problem

    I adjusted the turret speed adjustment and was able to get the turret to index to the correct station but it will still over index every so often. I ran a program and it works for the most part but...
  9. Replies
    0
    Views
    1,174

    Hardinge CHNC turret problem

    I'll try this section just to cover my bases. I am having trouble with the indexing on my Hardinge CHNC with an 0T control. After sitting for a couple of weeks, I fired up the Hardinge and am having...
  10. Replies
    4
    Views
    3,464

    Hardinge chnc turret problem

    Fired up my hardinge chnc with fanuc 0t control after sitting for a couple of weeks and am having trouble with the turret. I can index it in the jog mode about 4 or 5 times and it will finally hang...
  11. Replies
    4
    Views
    2,014

    Miyano single block issue

    The miyano is up and running, it was the parts catcher.Your post about the bar feeder got us thinking and we found out that when the parts catcher was in the retract position it was not making the...
  12. CNC Outsourcing

    If you have the talent the work the room and the power get your self a cnc.There is no feeling in the world like watching the machine run verses turning handles and if you tool it right there is no...
  13. Replies
    15
    Views
    3,977

    Hardinge CHNC1 E-Stop issue

    Just getting back to all that helped on this problem, it was the coolant pump.It must have been a little to cold in the shop when I fired it up and the fact that I use a fairly heavy duty cutting oil...
  14. Replies
    4
    Views
    2,014

    Miyano single block problem

    We checked out the door interlock switch and it is working,we also checked out the way lube pump and thats working.It's like you have to jump start the program to get it to run,it's weird and as you...
  15. Replies
    4
    Views
    2,014

    Miyano single block issue

    We have a Miyano BNC-34 turning center with a Fanuc 3T control that is giving us some problems, maybe some of you folks out there can lead us in a direction for trouble shooting this machine.The...
  16. Replies
    15
    Views
    3,977

    Hardinge CHNC1 E-stop problem

    Thanks for all the feed back, I ordered a wiring diagram for the machine today hope to have it in a day or two.Talked to Hardinge today and they think the problem is relative to the coolant pump,he...
  17. Replies
    15
    Views
    3,977

    Hardinge CHNC1 E-stop problem

    The axis were not moving at the time it shut down and I checked the way lube and its topped off,the coolant pump breaker was not tripped and no signals or alarms other than zero out the x and z axis...
  18. Replies
    15
    Views
    3,977

    Hardinge chnc1 E-stop problem

    Thanks for the input but no luck yet,the only message I get is a #2003 telling me to zero return my x and z axis but I can't do that till I get out of the e-stop condition.The shop is on the cold...
  19. Replies
    15
    Views
    3,977

    Hardinge CHNC1 E-Stop problem

    My Hardinge CHNC1 with a fanuc 0T control is stuck in a e-stop condition.The machine was warming up at 500 rpm with the collant on and it just went into e-stop, there are no messages or alarms and it...
  20. Replies
    0
    Views
    891

    Hardinge UPV2000 Board

    Anyone know were I can get a good deal on a Allen Bradley UPV 2000 memory board (it's the one that replaces the upg, uph and the bulk memory supply and battery) on the Hardinge CHNC with the AB 7300...
  21. Replies
    2
    Views
    1,144

    AB 7300 (32K machine)

    AB 7300 (32K machine)
  22. Replies
    2
    Views
    1,144

    Can any one tell me how to hook up a DSI tape...

    Can any one tell me how to hook up a DSI tape punch model LRP-300X. I would like to set it up to pull tapes off my computer and allso off my Hardinge CHNC lathe with an allen bradley control.What...
  23. Replies
    0
    Views
    596

    Can any one tell me how to hook up a SDI tape...

    Can any one tell me how to hook up a SDI tape punch model LRP-300X. I would like to set it up to pull tapes off my computer and allso off my Hardinge CHNC lathe with an allen bradley control.What...
  24. Replies
    18
    Views
    2,476

    Have you tried increasing your retract feed rate...

    Have you tried increasing your retract feed rate on the way out.With a floating holder I would have a feed rate of .0500 going in and a rate of .0505 on the way out.To be honest with you I single...
  25. Replies
    55
    Views
    5,698

    I think all the smart shops are going to start...

    I think all the smart shops are going to start growing there own CNC machinists with kids that want to learn the trade(there are a few out there)and once they get it, pay them what they are worth so...
Results 1 to 25 of 121
Page 1 of 5 1 2 3 4