Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: GuntisK

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    11
    Views
    920

    Hello Lenebm! Parameters of my machine is in...

    Hello Lenebm!
    Parameters of my machine is in attachements (see pictures). Hope something from that can be useful for You.
  2. Replies
    11
    Views
    920

    I can take a photo of my machine parameters (I...

    I can take a photo of my machine parameters (I have QT-15SP with subspindle, but most parameters should be similar for QT-15U) if there is still a need for those.
  3. MAZAK QUICK SLANT 30 parameters, manuals & related questions

    Hello everyone! :)
    There is a chance of getting two repairable MAZAK Quick Slant 30 4-axis lathes. But before making any moves towards them I want to find some more information.:scratchchin: Maybe...
  4. Thread: QT 18 no start

    by GuntisK
    Replies
    4
    Views
    776

    Replace capacitors, the same goes for burned...

    Replace capacitors, the same goes for burned components (I see a diode and two small SMT capacitors near electrolytic caps- change these too, as electrolyte leakage do a damage both to components and...
  5. Replies
    0
    Views
    618

    Mitsubishi DWC-110H floppy disc copying

    Hi!
    So a question here- have someone managed to make a copies of program floppies that goes with these machines? I already know that common PC floppy drive can't read these in usual way. Would love...
  6. Replies
    23
    Views
    9,325

    Hello everyone here! :) Previous week bring to...

    Hello everyone here! :)
    Previous week bring to my shop DWC-110H, built 1989, system W7C. Could someone share system reloading procedure? There are three 3.5 floppies with machine. Maybe some of You...
  7. Replies
    4
    Views
    1,052

    No doubt it can be fun part with all that. :D...

    No doubt it can be fun part with all that. :D Fact that there are connectors is good. I have experience with industrial electronic,both repair and retrofitting so there should be no problems.
    SLA...
  8. Replies
    4
    Views
    1,052

    Thanks SteveEx30! ;) One question more- how...

    Thanks SteveEx30! ;)
    One question more- how complicate and time consuming is disconnection of EDM machine from control unit? Are there connectors or everything is hard-wired?
  9. Replies
    4
    Views
    1,052

    Mitsubishi DWC-110H parts weight

    Hello everyone here!
    Recently Im looking on Mitsubishi DWC-110H wire edm (year 1989). Its in working state, comes with all manuals and data carriers (as seller said). I would really like to know...
  10. Replies
    1
    Views
    1,317

    OKUMA BDU-30A manual?

    Hi to everyone!
    Recently I bought an OKUMA MC-4VA machining center, looks a very promising machine. :)Unfortunately servo drives drop an error, first insight in these shows some output transistors...
  11. Replies
    11
    Views
    1,754

    There is a full circuit for DK434 in FR-SE...

    There is a full circuit for DK434 in FR-SE manual. ;)More interesting would be DK456 or BKO-C1877 inner circuit.
  12. Replies
    10
    Views
    1,235

    There is one very simple way to check IGBT...

    There is one very simple way to check IGBT transistors. For that You need to have power supply with output voltage between 12 to 15V. Next thing to have is crocodile wires and light bulb from the car...
  13. Replies
    10
    Views
    1,235

    Check power stage of VFD. Take a look on diode...

    Check power stage of VFD. Take a look on diode rectifier, check those large electrolytic capacitors (they can be in short circuit state. It tends to happen when they became old.). And yes- IGBTs and...
  14. Replies
    8
    Views
    1,032

    Exactly my case. Check LED lights on servo pack...

    Exactly my case. Check LED lights on servo pack and external controller- if they are dim then there is a problems with power. Measure voltage on contactor (phase to phase)- it is very possible some...
  15. Replies
    8
    Views
    1,032

    I have QT15 with sub chuck option. What exactly...

    I have QT15 with sub chuck option. What exactly is the error? I had a bad contactor problem and dead optocoupler in servo driver. After replacing everything works.
  16. Replies
    2
    Views
    814

    Thats nice to hear. :)

    Thats nice to hear. :)
  17. Replies
    2
    Views
    814

    Statistics on SF-CA card problems

    Hello to everyone here!
    This time something like a little poll. As we all know number one problem in Mazak electronics is VFD. Im interested about SF-CA board that lives in Mitsubishi FR-SF- do You...
  18. I have a suspicion it is. If only there would be...

    I have a suspicion it is. If only there would be at least some example available... :scratchchin:
  19. The same here- got a QT15 with subspindle that I...

    The same here- got a QT15 with subspindle that I have used only as tailstock. Have a large amount of manuals with machine but nowhere is an instruction on using subspindle. Only difference here is...
  20. Actually there is connection between both power...

    Actually there is connection between both power supply and aging IGBT, but even that's not all (these two are typical problems). IGBT is just like tyres for Your car- it has some resource, different...
  21. There is really no space high-tech in those older...

    There is really no space high-tech in those older Mitsubishi IGBT drivers. There is a couple reasons why they die- bad power supply, bad IGBT due to aging. Basically thats all. It is possible to make...
  22. It shows Production hours: 46770. For now it...

    It shows Production hours: 46770. For now it seems that maintenance is like typical for any other CO2 metalworking laser.
  23. Mazak laser path turbo-x48 - pros and cons

    One of my friend is looking into buying a laser - Mazak laser path turbo-x48. What are the pros and cons of this machine? What are typical problems for these particular machines? Is it worth it? One...
  24. Plus to mentioned above, the problem could also...

    Plus to mentioned above, the problem could also be in power portion of FR-SF. Big electrolitic capacitors can be bad (its just a question of time for those. El.caps are the first component that fails...
  25. Replies
    25
    Views
    2,446

    I looked the videos- so here is some question...

    I looked the videos- so here is some question regarding one called 16 augusti 2018. Is that some plug on chuck hydrocylinder? There is noticeable wobbling of cylinder in video. Maybe some centrifugal...
Results 1 to 25 of 44
Page 1 of 2 1 2