Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: macchi7

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    31
    Views
    1,597

    As others have said here, it's an Eazi Out. The...

    As others have said here, it's an Eazi Out. The worst name by which it could ever be described as and the company should have been prosecuted under trades description. A more apt name would have been...
  2. Replies
    1
    Views
    1,047

    Have you tried contacting Zaklady in Tarnow,...

    Have you tried contacting Zaklady in Tarnow, Poland? Although they are now listed as armaments manufacturers, I have always found the Polish to be very helpful. They may just be able to help.
  3. Replies
    28
    Views
    3,500

    That table looks in very good condition. Please...

    That table looks in very good condition. Please tell me you aren't going to weld on it!
    I got a bollicking off our works manager because he found me scraping protective coating off a new to us table...
  4. In my experience, eastern europeans can come...

    In my experience, eastern europeans can come across as aggresive and pushy. Even so, no reason for this guy to go on the way he did. Sorry I'm busy is a pretty understandable statement to most folks
  5. Thread: Cazeneuve 500

    by macchi7
    Replies
    11
    Views
    1,800

    I have a manual for the 500/575/725 series...

    I have a manual for the 500/575/725 series lathes. Send me an email to [email protected] and I will send you a copy
    Gary
  6. A big "tie wrap" or "zip tie"? Cheap to buy,...

    A big "tie wrap" or "zip tie"?
    Cheap to buy, easy to install and remove
  7. Replies
    7
    Views
    893

    What is the application of the Hirth coupling?...

    What is the application of the Hirth coupling? This coupling was popular for coupling crankshafts on twin cylinder 2 stroke motorcycle engines in the 1960s
  8. Replies
    8
    Views
    1,217

    Some machines do use an M10 x 1.25 thread for...

    Some machines do use an M10 x 1.25 thread for their mirrors, and some have a right hand thread on the right side and left hand on the left side. This may be so they don't loosen in the wind? For any...
  9. Replies
    4
    Views
    1,460

    I had an early 540 and found that hand cranking...

    I had an early 540 and found that hand cranking from "low" to "high" was a pain. I did look into removing the plate at the bottom of the vertical hand feed shaft and putting on a motor drive, but...
  10. Replies
    18
    Views
    3,529

    Hi Luke The correct oil for the machine is...

    Hi Luke
    The correct oil for the machine is Velocite 3, which is like paraffin. If your manager has used hydraulic oil, let him know, from me, that he is a tit. He has just reduced a precision...
  11. Replies
    3
    Views
    1,297

    Can you make a new quill where the wheels can be...

    Can you make a new quill where the wheels can be secured with a screw? Much quicker and easier to change internal wheels this way. Any chance of a photo of your current set up?
  12. I would use a 4 jaw chuck in the headstock of a...

    I would use a 4 jaw chuck in the headstock of a cylindrical grinder and a female "half centre" in the tailstock to allow access along the full length of the stem. Make sure there is a chamfer on the...
  13. Replies
    10
    Views
    856

    Stating the obvious here, they are to tap a...

    Stating the obvious here, they are to tap a 7/8"-32 left hand hole, though goodness knows what in. I reckon they are adjustable as the part being made is hardened and may shrink in that process....
  14. Send me your email to [email protected] ...

    Send me your email to
    [email protected]
    and I will send you a drawing by return
    Gary
  15. Replies
    3
    Views
    992

    I have a manual scanned. Send me a PM with your...

    I have a manual scanned. Send me a PM with your email address
  16. I have a Moore No.3 and it is a wonderful...

    I have a Moore No.3 and it is a wonderful machine. I also have the details of the quill taper which is unique to Moore and can dig the data out for you if you decide to make anything as some adapters...
  17. What is the taper in your machine? I am...

    What is the taper in your machine? I am suspecting that if it is obsolete, it may only be small and an ER25 collet and its holding capacity will be too much for your machine.
    Easy enough to make a...
  18. A bit off topic, but I've just had to make some...

    A bit off topic, but I've just had to make some footrests for a 1960s Italian motorcycle which had a very coarse knurl on them of 4 mm pitch. Did a 12 start thread, 48mm lead at 4mm pitch, left and...
  19. Replies
    34
    Views
    2,585

    They are called "Very Nears" for a reason!

    They are called "Very Nears" for a reason!
  20. Replies
    27
    Views
    3,160

    If a 4 jaw can't do what you require, how about...

    If a 4 jaw can't do what you require, how about collets? As suggested, maybe a "Griptru", but still a mess on to get it to run true. What is the job which requires such accuracy from a chuck?
  21. I did just the same to get a Bridgeport into a...

    I did just the same to get a Bridgeport into a friends workshop. No real problems in getting the table off, but it will need at least 2 of you due to the weight. Put it back on straight away if you...
  22. Replies
    24
    Views
    2,628

    I used Goodwins a few years ago to replace a...

    I used Goodwins a few years ago to replace a broken Heidenhain scale on my Moore jig borer. Phoned them and spoke directly to the owner of the outfit who I found to be very helpful. I too have...
  23. Replies
    17
    Views
    1,385

    I'm with you on that one!

    I'm with you on that one!
  24. You could compare the rougher 2 to Acme thread...

    You could compare the rougher 2 to Acme thread data published on the web or a Machinerys Handbook. A couple of measurements will confirm what you have. Can you post a picture of the tap wrench you...
  25. Replies
    17
    Views
    1,385

    A bit of a clue for us all would be what...

    A bit of a clue for us all would be what graduations there are on the handwheel (ie what one full turn would be) and how many starts there are. That would help to find the correct pitch/lead. Also is...
Results 1 to 25 of 69
Page 1 of 3 1 2 3