Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Hartkem

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    263

    Hendeyman, Thank you I’ll do them same.

    Hendeyman,

    Thank you I’ll do them same.
  2. Replies
    2
    Views
    263

    Hendey 12x30 Spindle Clutch Oil Cup

    My 12x30 Hendey is missing the Gitís oil cup on the spindle clutch engagement collar. Iíve been squirting oil into the threaded hole to get by for now. Did the original Oiler have a wick? I found a...
  3. Replies
    6
    Views
    607

    I think it’s just my expectation of the machine....

    I think it’s just my expectation of the machine. I went through every inch of this machine including the dog clutch mechanism. I’m going to limit the feed mechanism operation to 600 and below and try...
  4. Replies
    6
    Views
    607

    Hendey 12x30 gear train noise

    284379

    I cut my first chips on my Hendey today after a 10 month long restoration. My lathe is a 12 speed model but has the two speed motor option. Top speed is 1195. The headstock sounds very...
  5. Replies
    12
    Views
    1,711

    Got some more done on the Bridgeport today. Took...

    Got some more done on the Bridgeport today. Took the bed and saddle off. Found multiple plugged oil holes and one plugged metering unit. I cleaned out all the oil holes and oil worm trails and...
  6. Replies
    12
    Views
    1,711

    Yes there is an in-line lubricator. It needs some...

    Yes there is an in-line lubricator. It needs some attention though. I need to remove the table as I’m pretty sure one of the 4 lines are plugged to the x axis. I’ll check the nut at that time.
  7. Replies
    12
    Views
    1,711

    .075” x axis backlash with the table in the...

    .075” x axis backlash with the table in the center. .070” with the table on the ends. Screw looks good and being the backlash is relatively even I suspect the issue is with the nut. Also found the...
  8. Replies
    12
    Views
    1,711

    I spent about 2 hours cleaning the machine. I...

    I spent about 2 hours cleaning the machine. I have a few hours to go. I ordered a new 14” flat smooth file for the table. I did run it without a tool in it so that could be the noise (don’t have any...
  9. Replies
    12
    Views
    1,711

    Bridgeport - new to me with questions

    Very excited about my new to me 2J Bridgeport purchase. I was picky about the way condition and I am happy with my final decision. The table has a lot of little dings in it and some surface rust....
  10. Replies
    0
    Views
    566

    Bridgeport way inspection - 3rd machine

    Hereís the way pics of the third machine of the seller who says the ways have been touched up with a disc sander.
  11. Yes the seller of the first two is a dealer. The...

    Yes the seller of the first two is a dealer. The tilted head machine with power draw bar has clean ways but has not been evaluated by seller. Don’t think he’s willing to evaluate condition for the...
  12. I couldn’t add pics of last machine due to max of...

    I couldn’t add pics of last machine due to max of 5
  13. Bridgeport way inspection - potential purchase

    Iím on the hunt for a used J head Bridgeport since my wife gave me the go ahead to make the purchase. I have a couple Hendey lathes but this will be my first real Mill. New upgraded Budget is...
  14. Replies
    0
    Views
    681

    WTB Bridgeport J head Mill

    I may be looking for a unicorn but in search of a J head Bridgeport mill that has minimal wear. Iím not concerned if itís a belt or vari head or if it has DRO or power feeds. I can add that later. My...
  15. Replies
    11
    Views
    3,237

    I sent you a PM

    I sent you a PM
  16. Replies
    11
    Views
    3,237

    Iím interested but Iím a little far away in...

    Iím interested but Iím a little far away in Missouri. How easily is this removed from its location? What part of Kentucky?

    Thanks
    Mike Hartke
  17. Replies
    6
    Views
    597

    There was a rubber piece between the spacer and...

    There was a rubber piece between the spacer and washer that I assumed was added by a prior owner. There was also one under one of the two square headed bolts that lift the motor plate. Is there any...
  18. Replies
    6
    Views
    597

    Thanks. I also have the 18 speed version but it...

    Thanks. I also have the 18 speed version but it seems different.
  19. Replies
    6
    Views
    597

    Hendey 12x30 Motor mount

    Can anyone take a picture or describe how these parts are supposed to be assembled for the motor mount? This lathe is a 12 speed gear head with a two speed Westinghouse 3 phase motor.
  20. Replies
    0
    Views
    288

    WTB Hendey 12x30 Belt Guard

    Missing a few items for this lathe I'm restoring. I need the missing pieces in this photo. The door and the drop in insert. Also need a quick change gear box cover. Hendey 12x30 12 Speed
    ...
  21. Thanks for that information. Makes sense now.

    Thanks for that information. Makes sense now.
  22. Hendey frame 284 2 speed Motor bearing lubrication

    Heading towards the end of my 12x30 gear head restoration and am now starting on the motor / wiring. I took the end covers off the 3hp two speed three phase motor Westinghouse motor and found grease...
  23. Replies
    3
    Views
    776

    Some pictures of what I did regarding the oil...

    Some pictures of what I did regarding the oil wicks and felt.

    273894
    273893
  24. Thank you for that

    Thank you for that
  25. Replies
    3
    Views
    776

    Hendey Apron Sealant and oil wicks

    Finishing up the apron reassembly on my 12x30 12 speed gear head lathe. Did Hendey use any type of sealant between the two halves? I currently have it back together with no sealant. Also, I found two...
Results 1 to 25 of 47
Page 1 of 2 1 2