Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: david n

Page 1 of 60 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    35
    Views
    2,310

    "Sales rep rubs you the wrong...

    "Sales rep rubs you the wrong way"............................that's close to 97% of 'em...................They are always your buddy. They laugh at stupid stuff. They try to relate to you by finding...
  2. It's a Mini Mill.............there's no reason...

    It's a Mini Mill.............there's no reason whatsoever to place it on urethane. I don't think there's MTB out there that would suggest placing a VMC on rubber pads..................Every shake and...
  3. No rubber............you will likely see more...

    No rubber............you will likely see more vibration..................not in the floor, but in the machine.
  4. Replies
    17
    Views
    1,098

    Sounds more like a process problem vs machine...

    Sounds more like a process problem vs machine problem.
  5. Haas VF2 and SL20 Control Panels for sale................

    I have a control panel off of a 2004 VF2. Color monitor. Remote Jog Wheel. 3.5 floppy drive. $450.00+ shipping.
    271678

    271679

    The other is a panel off of a 2006 SL20. Color monitor. USB drive....
  6. Replies
    17
    Views
    1,098

    Lynx 220LC here............fast and accurate....

    Lynx 220LC here............fast and accurate. I'll have a few tenths movement from cold to warm(coolant like bath water)............Holding tenths is no problem.
  7. Only needs to be "new" to...

    Only needs to be "new" to YOU.........................
  8. Replies
    706
    Views
    167,676

    Happy Thanksgiving folks................grateful...

    Happy Thanksgiving folks................grateful for all the Lord has done for me..............................

    The boy had fun with an old saw blade............enjoyed it so much I told him he's...
  9. I run the same parts on my Doosan DNM500 as I ran...

    I run the same parts on my Doosan DNM500 as I ran on my VF2...............less inserts, less end mills, less noise, less scrap........It's nice to run a 1" inserted end mill or 3" face mill and not...
  10. Heck no!.............$70 to swap it out(which...

    Heck no!.............$70 to swap it out(which ain't too bad)..................
  11. Ugh...........lugger was swapped out this week....

    Ugh...........lugger was swapped out this week. 6k #'s of Ali.............$.12/lb...............
  12. Some specialty 3/4" drive sockets............. ...

    Some specialty 3/4" drive sockets.............

    https://live.staticflickr.com/65535/49102315157_942bb0aabf_k.jpg

    https://live.staticflickr.com/65535/49102315227_72d3391ee6_k.jpg
    ...
  13. Replies
    103
    Views
    8,299

    So a few less key strokes are worth more that...

    So a few less key strokes are worth more that making parts that don't need to get baby sat? Worth more than the savings in less inserts, drills, and end mills? Worth more than not getting service on...
  14. Replies
    103
    Views
    8,299

    I'm very happy with the two Doosan machines I...

    I'm very happy with the two Doosan machines I have on my floor, Lynx 220LC and a DNM 500. The little Lynx is fast and accurate. And the mill is heavy and rigid. They both are leaps and bounds ahead...
  15. Replies
    46
    Views
    3,262

    Cast has pores.......................

    Cast has pores.......................
  16. Replies
    46
    Views
    3,262

    I have some Lodge pans..................Angle...

    I have some Lodge pans..................Angle grinder with a flap disc followed by an orbital sander...........perfect pre-seasoned cook surface in less than 15 minutes.

    Can you get Durabar in...
  17. Replies
    706
    Views
    167,676

    The center fixed jaw is one solid piece. No...

    The center fixed jaw is one solid piece. No individual hard jaws. Kinda like it. No bolts holes to fill with chips......................

    The grooves are for those Talon Grips.............I've...
  18. Replies
    706
    Views
    167,676

    First part on em'...................I have a few...

    First part on em'...................I have a few jobs that will require all four on the table.......................fit and finish on the vises is really nice. Sol has got 'er together over...
  19. Replies
    706
    Views
    167,676

    .............................. ...

    ..............................


    https://live.staticflickr.com/65535/49030754412_5d1668d793_k.jpg

    ...............................
  20. Rotary transfer machines use "turning" heads like...

    Rotary transfer machines use "turning" heads like that......................


    https://www.youtube.com/watch?v=HHttjypB8q4
  21. Replies
    14
    Views
    5,517

    Fixed it..................

    Fixed it..................
  22. I had one of those apart years and years...

    I had one of those apart years and years ago..................I think the cam can be adjusted? Or is the cam itself just plain worn out? Never had problems cutting miters...............
  23. Replies
    260
    Views
    52,045

    The OP is most people...

    The OP is most people nowadays..........................
  24. Replies
    260
    Views
    52,045

    Not someone trollin'...............but someone...

    Not someone trollin'...............but someone that hasn't the foggiest of what goes in to mfg these days. The OP more than likely tucked his tail between his legs and went home.....................
  25. Replies
    260
    Views
    52,045

    Yeah? So. What's your...

    Yeah? So. What's your point?...................................:D
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4