Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: JohnEvans

Page 1 of 60 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    7
    Views
    515

    The way the turret attaches to the main body is...

    The way the turret attaches to the main body is not the way BP did it. BP's had 4 pockets with nuts retaining the turret. This thing has 2 horizontal nuts to the rear to lock the swiveling of the...
  2. Well my experience was with air cooled MC's but...

    Well my experience was with air cooled MC's but does the valve guide have a lube supply? Did a old 40s Norton at customer insistence with bronze and it Stuck! Engine in question relied on oily vapor...
  3. Replies
    12
    Views
    671

    WD 40 gets gummy also,use spindle oil same as...

    WD 40 gets gummy also,use spindle oil same as head bearings use.
  4. Replies
    5
    Views
    401

    No prob ,just put them back in the drawer.

    No prob ,just put them back in the drawer.
  5. Replies
    53
    Views
    2,395

    Don't see a link !!

    Don't see a link !!
  6. Replies
    5
    Views
    401

    See additional picture . Has had a bit ground off...

    See additional picture . Has had a bit ground off for clearance [internal dia. work?] Can't see how that would have any negative effect on function of the holder.
  7. Replies
    5
    Views
    401

    These are excess to me. Seco MWLNR 12-4B & a...

    These are excess to me. Seco MWLNR 12-4B & a MWLNL 12-4B plus a 10 pack of WNMG 432 assorted inserts.Top of shank have about .060 milled off to fit smaller holders. Anyway $125 shipped . Paypal only...
  8. Replies
    29
    Views
    1,819

    If the spindle in question is on a Logan-South...

    If the spindle in question is on a Logan-South Bend-Atlas or similar and a 1.5 diameter 99% it is 8 thread as that size is very common on those machines. Get a decent thread gauge solve the whole...
  9. All I have ever done [admittedly not a lot] I...

    All I have ever done [admittedly not a lot] I just use the white coated rod. Also bare rod with the caned white or pinkish flux. Sil-Bronze is usually used with TIG IME. Larger repairs with a lot of...
  10. Replies
    1
    Views
    601

    Sale ended

    Items sold locally. Thanks for looking
  11. Replies
    1
    Views
    601

    Carbide End Mills

    Picked up a small lot of end mills recently these are excess to my needs.
    1 Lot of 9 1" shank re-sharps smallest is .875 rest seen to be .979-.990. one ball end all seem sharp some still in wax....
  12. News to me ,never seen that style . And I'll bet...

    News to me ,never seen that style . And I'll bet they are as popular has buggy whip sockets !LOL
  13. Replies
    0
    Views
    340

    Assorted Die Heads 7 piece lot

    Again these are for a friend that is down sizing and moving shop. This stuff has been in the darkest corner for years and is Dirty !! Saw 1 Landis and didn't look to close at the rest.This is...
  14. Bridgeport 40 Taper holder lot 21 pieces

    OK first off doing these for a friend ,he has been down seizing and moving shop. Stuff is dirty but did not see and rust pitting . These have the pull stud made as part of the holder and all of them...
  15. If that mill is anything like a Bridgeport the...

    If that mill is anything like a Bridgeport the someone was the factory for the sheet metal piece! It is a chip guard to keep out chips etc. when the spindle is close to fully extended. Or was the...
  16. Replies
    1
    Views
    160

    Search with the German spelling "Komet" on...

    Search with the German spelling "Komet" on google. I had some insert style turning tools from Komet and needed info on the inserts. Your set is for boring.
  17. Probably stuck on with sealer . Take a old pocket...

    Probably stuck on with sealer . Take a old pocket knife blade and a small hammer and tap the blade down between the front plate and main casting in several places around the edge. I have used that...
  18. Replies
    5
    Views
    826

    You got to be kidding without pictures!!!

    You got to be kidding without pictures!!!
  19. OFFERS ? On these Bars & Inserts

    SOLD !!Rather sell here than eBay.Got more small BB than I'll ever use.
  20. Replies
    19
    Views
    1,247

    Even better yet, I found the exact gear parted...

    Even better yet, I found the exact gear parted out on eBay for $50.

    philip[/QUOTE]

    You better go buy a lottery ticket or 2 !! Good for you ,amazing what pops up on eBay.
  21. Replies
    2
    Views
    531

    Try "Chapman MFG" they make all sorts of Torx-hex...

    Try "Chapman MFG" they make all sorts of Torx-hex etc. bits.
  22. FS Circle boring bars L&R 1/4X5 + 2 boxes of inserts see pix

    I was looking for something else today and found these bars and inserts tucked away,forgot I even had them. New unused ,bought from a tool-die shop closing. See the pictures for details ,bars are...
  23. If auto trans no issue using left foot,stick not...

    If auto trans no issue using left foot,stick not so easy !
  24. Replies
    19
    Views
    1,247

    Rule 1 when dealing with old machine tools IF the...

    Rule 1 when dealing with old machine tools IF the needed part is available ,be happy pay up.
    Rule 2 either make/repair or do without [rule also applies when the part is not available]
    I recently...
  25. Replies
    5
    Views
    747

    Interesting gap bed with threaded spindle, seems...

    Interesting gap bed with threaded spindle, seems like kinda of a odd combination. Also looks like it may have a clutch & brake going by the one lever lower right on head stock.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4