Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Tony Quiring

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. If one blade cracked then remove all of the...

    If one blade cracked then remove all of the weakened part.

    Not remove material from blades opposite it.

    If even number just one, if odd number 2.

    Make a mandrel with ball bearings to support...
  2. Likely for a Yale jack Or take it to a...

    Likely for a Yale jack

    Or take it to a bearing supply and see what they can come up with.

    Sent from my SM-G781V using Tapatalk
  3. Replies
    4
    Views
    363

    Slow blow fuse or circuit breaker. Leaving on...

    Slow blow fuse or circuit breaker.

    Leaving on costs $$$

    Sent from my SM-G781V using Tapatalk
  4. Replies
    29
    Views
    2,603

    If aluminum extruded. If other things lost wax...

    If aluminum extruded.

    If other things lost wax or very xpensive milling or EDM.



    Sent from my SM-G781V using Tapatalk
  5. Replies
    9
    Views
    10,201

    Right click anywhere on the desktop screen and...

    Right click anywhere on the desktop screen and look for resolution.

    Different versions slightly different so you may need to hunt.

    Your screen resolution. May be too low, try a different one....
  6. I like the magnetic spinning disk, properly done...

    I like the magnetic spinning disk, properly done would be nice ornament running next to the Atmos clock.

    As a prank tool the ticking noise could be used to drive someone nuts placed hidden in...
  7. Replies
    11
    Views
    1,300

    Cal the manufacturer of the unit, simple. If...

    Cal the manufacturer of the unit, simple.

    If it is under warranty than the manufacturer takes care of it.

    100 dollar deductible for house warranty should be refunded as they should not have...
  8. Way too much time on their hands. The use of...

    Way too much time on their hands.

    The use of all of the off the shelf stuff makes it far less interesting and since it is a lot of the same things repeated quite boring after a short while.

    The...
  9. N connector can do upto 2kw peak power. In a...

    N connector can do upto 2kw peak power.

    In a multi-transmitter combiner where 10 70 watt transmitters are combined.

    Granted combiner losses put the average power per unit maybe 40 watts there...
  10. Replies
    22
    Views
    1,616

    Years ago we had an automotive aftermarket cruise...

    Years ago we had an automotive aftermarket cruise control that had a flow sensor you added to the fuel line and it measured flow and gave you instant MPG.

    maybe creativ Amazon searches may find...
  11. Replies
    25
    Views
    2,027

    The belt should run in the center as the crown...

    The belt should run in the center as the crown causes the belt to climb.

    If it is riding on an edge the shafts are not parallel or in same plane.

    Sent from my SM-G781V using Tapatalk
  12. I was being nice... Many contractors and...

    I was being nice...

    Many contractors and suppliers had my photo on their dart boards.

    It seems there are 2 sides at the lowest level.

    The client accepts the poor stuff because they went with...
  13. At Nextel we had a bunch of sites get a bunch of...

    At Nextel we had a bunch of sites get a bunch of weird and wonky problems.

    They used 2 coax network systems, one was frequency standard and other was eithernet via coax.

    At each device was a...
  14. Replies
    55
    Views
    5,145

    In books they show a press used to bend cranks...

    In books they show a press used to bend cranks straight.

    In our shop it was hammer and chisel, a few hits on the low side relieves stresses and crank comes towards you.

    On a main bearing...
  15. Replies
    55
    Views
    5,145

    First, does it run true right now as is? We...

    First, does it run true right now as is?

    We worked in the crank department way back, we were "helper" so we polished finished cranks but straightened camshafts and the welded crankshafts.

    If...
  16. Replies
    14
    Views
    1,828

    What he said... Look at visual basic. As it is...

    What he said...

    Look at visual basic. As it is common for things like access.

    You need to define local and global variables and many other "processes".

    The write comments first is a good...
  17. Better here just get 2 small irons and heat both...

    Better here just get 2 small irons and heat both ends at Sam time and lift it right off.

    If board is burned no need to get crazy, just dig out the black stuff then fill with epoxy.

    Rebuilt many...
  18. Spin up maybe? Way back in the day I read some...

    Spin up maybe?

    Way back in the day I read some articles where they had weights magneticly suspended and spun them very fast. Many thousands of RPM to then use stored energy to provide power for...
  19. Replies
    25
    Views
    2,459

    The trick is simple. Rats cannot see that well...

    The trick is simple.

    Rats cannot see that well so they travel along walls and rarely go into open as no protection and they cannot see well.

    2x4 make great walls and can be placed to direct...
  20. Replies
    25
    Views
    2,459

    Additional crew for places the cats cannot get...

    Additional crew for places the cats cannot get...
  21. Replies
    25
    Views
    2,459

    We got aggressive with rat traps and got a lot of...

    We got aggressive with rat traps and got a lot of them.


    Dam things would get in the membrane between roof and shop and you could see their foot prints as they ran.

    Got real good at setting...
  22. Replies
    25
    Views
    2,459

    OT RATS...Rats in the forklift!

    So we very rarely use the forklift, we built a battery box to allow home made battery kit and the 6 160 Amp hr cell site batteries were done and we got some replacements and got them in.

    Since...
  23. Limited resource field operations mode... If...

    Limited resource field operations mode...

    If diode then which one?

    First, if there are many in assorted random looking places then likely NOT a unique item like a Zener but instead generic use...
  24. Gerber multi-tool has saved many trips to the...

    Gerber multi-tool has saved many trips to the truck last 20 something years.

    Mail in warranty is great, it breaks you get RMA and send to Seatle and a brand new one arrives from...
  25. Replies
    26
    Views
    1,457

    If it failed once it will again... Maybe...

    If it failed once it will again...

    Maybe rewire is in order.

    If you can get to the wires then re-route them to another relay or contactor.

    Use this original mechanical device to control the...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4