Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: rakort

Page 1 of 16 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    561

    check this out the attached and feel free to...

    check this out the attached and feel free to research the same for similar information or keep asking and we'll help

    281987
  2. Replies
    27
    Views
    1,407

    Is this what we are talking about? 281679 ...

    Is this what we are talking about?

    281679

    281680

    I made new washers and cut some felt for it, but the circular snap ring I reused.
  3. Replies
    27
    Views
    1,407

    Me too, the picture thing is annoying!!

    Me too, the picture thing is annoying!!
  4. Replies
    11
    Views
    1,143

    Interesting that you bring up rag bond. I make...

    Interesting that you bring up rag bond. I make paper for a living (neenah.com)......in the day we did make paper from old rags / cotton linens, etc. Had a big tumbling "boiler" we use to cook them...
  5. Replies
    30
    Views
    1,921

    I'm interested in this pix for a number of...

    I'm interested in this pix for a number of reasons. I don't think I noticed this before.....

    #1 this is a super early RD

    #2 It has double v belt for the main drive....EARLY

    279736

    #3...
  6. Replies
    30
    Views
    1,921

    No we will not remove your post. But we are...

    No we will not remove your post.

    But we are happy to help. I'm still stoked on the $ you paid for the lathe and would love to see it.

    I'm not a retired engineer YET, but looking forward to...
  7. Replies
    10
    Views
    787

    Yes it does feed the saddle and will need to be...

    Yes it does feed the saddle and will need to be replaced. I did the same operation on my lathe somewhere around here.

    New to me Monarch 10EE just arrived!
  8. Replies
    30
    Views
    1,921

    With limited description, pictures will help tell...

    With limited description, pictures will help tell the story a lot better. Also research of the millions of pictures out there will help. Ohh BTW what year / model lathe is this?

    The only thing...
  9. Replies
    10
    Views
    2,936

    one more input from the community. I do have a...

    one more input from the community. I do have a hole in the bottom of my RD apron into the sight glass bore.

    278677
  10. Replies
    11
    Views
    1,002

    flip all those pieces over and take another...

    flip all those pieces over and take another picture please
  11. Replies
    4
    Views
    472

    No problem, let us know how it works out. I...

    No problem, let us know how it works out.

    I guessed at the 60" length......figured it was long enough though.
  12. Replies
    4
    Views
    472

    McMaster-Carr (https://www.mcmaster.com/1497k34)

    McMaster-Carr
  13. Replies
    5
    Views
    574

    Agreed, after I thought about it a minute the...

    Agreed, after I thought about it a minute the coarse screen is to support the felt/filter.
  14. Replies
    5
    Views
    574

    In my head I would go from the outside to the...

    In my head I would go from the outside to the inside with coarse screen, fine screen, felt. Get the rocks out first, then the sand, then the silt.
  15. Replies
    15
    Views
    1,375

    Not sure what is up.... You called it a...

    Not sure what is up....

    You called it a spacer. I believe Monarch calls it a deflector. I call it a flinger. That spacer is for flinging the oil that works its way through the bearings outward...
  16. Replies
    24
    Views
    4,201

    I found this sometime ago around here 275594

    I found this sometime ago around here

    275594
  17. Replies
    15
    Views
    1,375

    you can see in my picture (also from a round...

    you can see in my picture (also from a round dial) that it has the same bearings.

    I'm thinking the AC bearings were from a newer iteration of the gearbox design.

    As I recall I had a hard time...
  18. Replies
    15
    Views
    1,375

    I'm sure you cleaned out the oil drain back port...

    I'm sure you cleaned out the oil drain back port from outside the outer bearing, set the snap ring properly, and didn't cover it with a gasket, right?

    275119
  19. Replies
    24
    Views
    4,201

    I missed it initially......this thread died and...

    I missed it initially......this thread died and then jumped ahead 2 years....ooops.

    Vette dude are you still out there?
  20. Replies
    24
    Views
    4,201

    I'm all in for a clamp. Mark me down Are you...

    I'm all in for a clamp. Mark me down

    Are you making these for a round dial, square dial, or both? I understand the clamps are different. I'm interested in a round dial variety.
  21. Replies
    13
    Views
    1,144

    Electrical Schematic EE-2674 10EE SN 19377...

    Electrical Schematic EE-2674 10EE SN 19377
  22. Replies
    13
    Views
    1,144

    Couldn't make it to the end of this....was there...

    Couldn't make it to the end of this....was there a point in there some place?
  23. Replies
    13
    Views
    1,144

    Be warned. As Cal pointed out to me, Monarch...

    Be warned. As Cal pointed out to me, Monarch will offer only a "generic" documentation package for a round dial machine. They will have the original Machine SN card with the as delivered specs, but...
  24. Radwell has dug us out of more than one shit...

    Radwell has dug us out of more than one shit mess, but can't quite comprehend why buying a simple 10ee brush set would be put to them when they are easily available from the oem and likely else...
  25. Replies
    13
    Views
    1,144

    Is this an inline exciter? Can you share a pic...

    Is this an inline exciter? Can you share a pic of your MG drive unit?

    I've got reasonable copies of EE2442 (but not 2452) Can you verify the drawing #
Results 1 to 25 of 381
Page 1 of 16 1 2 3 4