Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: NRDock

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    17
    Views
    906

    At the start of the taper cutting process you...

    At the start of the taper cutting process you should see a demonstration of how the DOC affects surface finish. When you start making the taper the DOC will be very thin at the big end, and the...
  2. Replies
    17
    Views
    906

    Is this always the case, or just for tapers? I...

    Is this always the case, or just for tapers? I cut some tapers last weekend taking the backlash out going towards the work, and it worked just fine. More taper work this coming weekend, so if I'm...
  3. Replies
    68
    Views
    6,058

    If the 2 beams were merely in full contact, then...

    If the 2 beams were merely in full contact, then it seems the stiffness should be 1/8 * 2 = 1/4 that of a solid bar, not?
  4. Replies
    14
    Views
    1,394

    Headlamp! It's always shining where I'm looking. ...

    Headlamp! It's always shining where I'm looking.
    Tired of buying AAA's so I just ordered a pair of rechargeables off Amazon.

    I have an LED lightstorm over my lathe and nothing over my mill. ...
  5. Replies
    109
    Views
    6,329

    I have a friend who took on his squirrel problem...

    I have a friend who took on his squirrel problem with a Havahart trap and a sharp stick. He dispatched near a hundred before it slowed down enough to get boring. You can kill them faster than they...
  6. goober nonsense ie Poking along on remote...

    goober nonsense ie Poking along on remote back roads at 10-20 MPH
    May not be relevant to very many people, road hunters I guess.
  7. I just picked up a 2019 Raptor to replace a 2003...

    I just picked up a 2019 Raptor to replace a 2003 Chevy Silverado HD and a 5.0 Mustang. I ordered the Raptor without even driving one, since anything new was going to be way better than the 03 and no...
  8. Replies
    67
    Views
    4,224

    Just last week I was talking to a friend about my...

    Just last week I was talking to a friend about my 60" Kubota deck getting noisy after 15 years of abuse. He's a retired shop inspector working part time at the local tractor shop, favoring JD. He...
  9. Replies
    25
    Views
    1,564

    One should guess that lower strength bolts will...

    One should guess that lower strength bolts will contain less of the alloying elements that contribute to higher strength.
  10. Replies
    36
    Views
    3,823

    Seems they are out to screw everyone below...

    Seems they are out to screw everyone below themselves on the food chain to justify their existence.
    This is the cost of sending every other fuckwit to college. Some of them graduated! I fear the...
  11. RVB Precision | Welcome to the world of ultra...

    RVB Precision | Welcome to the world of ultra precision
    Here's Roy's web site.
  12. Replies
    25
    Views
    1,552

    Govnmnt work, Ten million, you might get the...

    Govnmnt work, Ten million, you might get the order.
    I'm a BSME, with 38 years experience, and still couldn't wrap my head around that print at first.
    We use 300 series SS all the time for heat...
  13. Replies
    7
    Views
    1,340

    Chernobyl is in Ukraine, Not Russia.

    Chernobyl is in Ukraine, Not Russia.
  14. Take a digital pic with camera settings to...

    Take a digital pic with camera settings to minimize distortion.
    Paste into Autocad.
    Zoom in.
    Zoom in some more.
    Draw lines over edges.
    Measure angle between lines.
  15. Replies
    40
    Views
    3,419

    Chernobyl: The History of a Nuclear Catastrophe,...

    Chernobyl: The History of a Nuclear Catastrophe, Atomic Adventures, and Atomic Accidents are all available on Audible.
    I recommend them all, but the latter part of Chernobyl is a tedious blame...
  16. Thanks Guys! I wonder how many different...

    Thanks Guys!
    I wonder how many different versions of the E510 there are?
    In my manual, 02-07 is indeed poles. 02-14 Doesn't exist. mksj, my page numbers don't match yours.
    My whole group 17...
  17. Replies
    66
    Views
    5,611

    When I bought mine about 04, I was convinced JD...

    When I bought mine about 04, I was convinced JD ground up money to make their green paint. looked like a 15% premium in a hard to compare market. OK, they do offer some nice features. I bought a...
  18. I hope he gets the max. Sometimes the only...

    I hope he gets the max.

    Sometimes the only meaning to ones life is to serve as a warning to others.

    Someone in our org decided we didn't need inspectors anymore. Just get the suppliers to...
  19. 2 Hp TECO E510 on a FRAY mill, 1200 RPM, 1 Hp, 230V motor

    Rather than bump my old thread, I'm starting over with a new problem. After a factory reset, and following the correct section of the correct manual, I have the mill running on the TECO. Starting...
  20. Replies
    5
    Views
    804

    OK, partially inserted tool makes sense for the...

    OK, partially inserted tool makes sense for the damage I'm seeing. I feel better not picturing some kind of horrendous crash.
  21. Replies
    5
    Views
    804

    What does it take to break a collet?

    I bought a used mill with a set of double angle collets for a NMTB30 holder, and yesterday I noticed the 1/2" collet is broken at one place on each end. The exposed face just has a subtle crack. ...
  22. Replies
    18
    Views
    1,498

    "Foundations of Mechanical Accuracy". Starts out...

    "Foundations of Mechanical Accuracy". Starts out interesting. A 14 hour flight may be the only way I'll ever get around to finishing it.
  23. Replies
    55
    Views
    6,101

    So, are you suggesting we nudge it towards...

    So, are you suggesting we nudge it towards California?
  24. Replies
    43
    Views
    2,905

    They get free beer. Honest, a case a month.

    They get free beer. Honest, a case a month.
  25. Replies
    2
    Views
    462

    TECO E510 on a 1200 RPM FRAY mill

    I've hooked up a 2 HP TECO E510 to the 1 Hp 1200 RPM motor on my Fray mill, but can't get the parameters right. It turns the spindle a few times before throwing a "CF08" Code. I've raised the PMSLV...
Results 1 to 25 of 115
Page 1 of 5 1 2 3 4