Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: MoriMillMan

Page 1 of 7 1 2 3 4

Search: Search took 0.00 seconds.

  1. Woops old thread

    Woops old thread
  2. Replies
    6
    Views
    654

    Jacobs taper 40 taper holders

    Command brand jacobs 3 and 4 sizes-30$ each or trade for setscrew or facemill holders

    Have 10+ available

    Sent from my SM-A115AP using Tapatalk
  3. Have a coworker crash another so you can make one...

    Have a coworker crash another so you can make one good probe. Ive had good luck with that.

    Sent from my SM-A115AP using Tapatalk
  4. Replies
    67
    Views
    5,516

    Got the new machine home today! Very puckered....

    Got the new machine home today! Very puckered. 5000# forklift was not enough had to tie off ass to the van...
  5. Sandvik 2" with 5 inserts my go to for any steel...

    Sandvik 2" with 5 inserts my go to for any steel under 34rc is .03-035doc 1500rpm 300-600ipm whatever stepover.
    1 1/4 with 3 inserts I run 170-300ipm 2000rpm I think
    1" with 2 inserts sounds like...
  6. I've had good luck with the sandvik 1 1/4" with...

    I've had good luck with the sandvik 1 1/4" with three inserts. We have a 1" with 2 inserts and it just sucks. The inserts last forever in steel and I've pushed them to .1 ipt .035doc 560sfm that was...
  7. Replies
    2
    Views
    290

    I though homemade too but if it is they really...

    I though homemade too but if it is they really made a nice replacement other than that shoulder. Nice round perfect looking oil grooves and all.

    I guess I'll add a spacer there.

    Sent from my...
  8. Replies
    2
    Views
    290

    Hendey rear bearing

    Hey something seems off to me here on my 16" 8speed Geared head. The rear spindle bearing housing has a flange / shoulder if I push it into place to register at the casting my view port is way past...
  9. Replies
    67
    Views
    5,516

    Dmg dmf 600l Sent from my SM-A115AP using...

    Dmg dmf 600l

    Sent from my SM-A115AP using Tapatalk
  10. Replies
    67
    Views
    5,516

    Lately I've been programing a lot of simultaneous...

    Lately I've been programing a lot of simultaneous xyz and swivel head to b90 rapid moves all that over a 109inch part then up and swivel across to the other end is very fun to watch. And even cuts...
  11. Replies
    67
    Views
    5,516

    I think mine is the same maybe more. Has the...

    I think mine is the same maybe more. Has the linear motor

    Sent from my SM-A115AP using Tapatalk
  12. Replies
    11
    Views
    1,932

    Not a dream, but I once had a night terror, where...

    Not a dream, but I once had a night terror, where i was trying to drill a hole with the probe..

    Sent from my SM-A115AP using Tapatalk
  13. Replies
    67
    Views
    5,516

    Wow thats slow I was hoping for 200-400 rapids...

    Wow thats slow I was hoping for 200-400 rapids haha...I just finished some big 4140 parts at work where I fed 550ipm so im going to be going through a shock phase here in the garage. I got spoiled...
  14. Id try 200-250 sfm .01 doc .002-3ipt Sent from...

    Id try 200-250 sfm .01 doc .002-3ipt

    Sent from my SM-A115AP using Tapatalk
  15. Replies
    67
    Views
    5,516

    Alright cool that sounds like a manageable...

    Alright cool that sounds like a manageable weight. Do you know what the rapids or feed max is? I dont want to run it faster or slower than intended by bostomatic

    Sent from my SM-A115AP using...
  16. Replies
    67
    Views
    5,516

    They sure seem like awful nice machines the 400...

    They sure seem like awful nice machines the 400 looked quite overbuilt. The ways were huge!

    I'll try to find that how its made

    Sent from my SM-A115AP using Tapatalk
  17. Replies
    67
    Views
    5,516

    I did read through a research paper on the...

    I did read through a research paper on the accuracy of the bostomatic 300. Very impressive for the 90s if I remember right most everything was repeating to .00005ish

    Sent from my SM-A115AP using...
  18. Haha I thought it would at least be useable... ...

    Haha
    I thought it would at least be useable...

    No worries I found an aloris cxa for 200 on ebay in some country I've never heard of. Looks lightly used. Tracking says its in NY now. I look...
  19. Replies
    67
    Views
    5,516

    Also did the tool changer come with fingers or...

    Also did the tool changer come with fingers or just a loose fit pocket?

    Sent from my SM-A115AP using Tapatalk
  20. Replies
    67
    Views
    5,516

    I'm actually settled on a 400, already...

    I'm actually settled on a 400, already retrofitted with a new siemens control.

    Ya it'll be tight but, no 300 for sale anywhere i see and it can be made to fit.

    You think its only 5000? Seems...
  21. Replies
    0
    Views
    261

    Swivel head milling techniques

    Hey guys i had a thought the other day about roughing on the dmg with 90deg b axis head. I was plunge millimg a slot and wondered what would happen if I swivel the head, 20 deg or so I think I...
  22. Replies
    67
    Views
    5,516

    Do you have a weight estimate for this machine? ...

    Do you have a weight estimate for this machine?

    Sent from my SM-A115AP using Tapatalk
  23. Replies
    3
    Views
    444

    Feel free to make offers Sent from my...

    Feel free to make offers

    Sent from my SM-A115AP using Tapatalk
  24. Replies
    3
    Views
    444

    Still for sale Sent from my SM-A115AP using...

    Still for sale

    Sent from my SM-A115AP using Tapatalk
  25. The quick change posts are still available, feel...

    The quick change posts are still available, feel free to make an offer if anyone is interested. Other 2 are sold.
    I now also have a garbage chinese aloros cxa 115$ new, if someone wants to pay...
Results 1 to 25 of 174
Page 1 of 7 1 2 3 4