Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Riggerson

Search: Search took 0.00 seconds.

  1. Just a follow-up in case anyone ever search for...

    Just a follow-up in case anyone ever search for this error.

    I decided to replace all 4 relays. I also found a bent tool changer finger. So I went ahead and also rebuilt the four worst pockets...
  2. It faulted again the same way after the shuttle...

    It faulted again the same way after the shuttle moved in. So almost positive it's a relay since the issue moved. I'll try polishing the relays I have and see if that fixes it (they checked good...
  3. I went through the boards and tightened all the...

    I went through the boards and tightened all the connectors. Didn't find anything obviously loose.

    While I was in there I swapped the K9-K12 relays.

    I booted it back up and the very first...
  4. I was in there putting in the dual battery...

    I was in there putting in the dual battery upgrade around the same timeframe all of this started happening. I had to remove the two top boards to get the battery off the bottom board. Thank you for...
  5. Intermittent Umbrella Tool Changer Alarm 115 Failure to Rotate

    I've got a 2012 Haas SMM that has the 10 tool changer. It's a fairly low hour machine.

    When I first got the machine after a couple months of running I got this alarm 115 (turret failure to...
  6. Replies
    0
    Views
    418

    RFQ - HT Small A2 Parts

    Looking for someone that can HT some small A2 parts. It's 4 parts. Largest is 7.5 diameter x 3.25 height. My normal source has extended lead time so hoping to find someone with furnace time that...
  7. Replies
    1,042
    Views
    195,160

    Vintage 6? Bridgeport Machinist Milling Vise -...

    Vintage 6? Bridgeport Machinist Milling Vise - Air Tools - North Decatur, Georgia | Facebook Marketplace

    Clean vise for sale. Just has a few issues.
  8. Replies
    0
    Views
    261

    WTB Surface Plate 48x36 Near ATL

    WTB Surface Plate 48x36 Near ATL

    Would consider freight shipping for the right plate.

    Probably going to buy a new standridge but if someone has something that's nice that they don't need that...
  9. Replies
    41
    Views
    2,828

    If you're only going to make a couple I'd do TIG...

    If you're only going to make a couple I'd do TIG and accept the reduced cycle time. You already own a MIG welder for general purpose work. TIG adds a ton of versatility to your shop. You can...
  10. Replies
    41
    Views
    2,828

    How many of those assemblies do you need to make?...

    How many of those assemblies do you need to make? If it's a lot then MIG setup is the way to go. If it's a handful I'd lean towards TIG.

    I'm skeptical of that laser welder with no provisions for...
  11. Replies
    6
    Views
    1,342

    I'm interested in the KM50 blank tool holders and...

    I'm interested in the KM50 blank tool holders and any other actual KM50 toolholders. I saw one blank in your bucket and then it's hard to tell what the rest are. I don't have any use for the okuma...
  12. Replies
    12
    Views
    2,097

    Your inbox is full. If you PM me I'll get in...

    Your inbox is full. If you PM me I'll get in touch with you. Thanks.
  13. Replies
    12
    Views
    2,097

    Can I pay shipping and will also pay to cover...

    Can I pay shipping and will also pay to cover your time to package it and ship to Atlanta? I don't have a good way to get up there.
  14. Replies
    0
    Views
    355

    wtb - 12 american standard t&g top jaws

    Have a 12" american standard tongue and groove chuck that lost its hardened top jaws. I have plenty of soft jaws but I'd like to have a set of hardened jaws to go with it. Thanks.
Results 1 to 14 of 14