Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Pathogen

Page 1 of 13 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    284

    I have run them until dead different brands. I...

    I have run them until dead different brands.

    I am very happy with the ones from the Big A

    Label on both say ULTRASONIC CLEANER

    and I don't have to keep taking them apart to fix them like the...
  2. Replies
    25
    Views
    1,211

    Watch this video on drilling SS YouTube...

    Watch this video on drilling SS

    YouTube

    And then a Greenlee should do it

    Got to clamp your work down solid!
  3. Replies
    12
    Views
    442

    Carbon Fibre is nasty. You shouldn't "blow it...

    Carbon Fibre is nasty. You shouldn't "blow it off" as a non health issue.

    At the very least add water to the vacuum stream and when you empty the tank be sure to dump it on land used to produce...
  4. Replies
    8
    Views
    580

    Here is a link to data sheet ...

    Here is a link to data sheet

    http://www.farnell.com/datasheets/2004026.pdf?_ga=2.244972741.1319397436.1581000971-22008874.1554745413

    Shows filament current 31 amps

    You can replace the tube...
  5. Replies
    6
    Views
    599

    The problems I encounter using Teflon (PTFE) is...

    The problems I encounter using Teflon (PTFE) is holding it in place.

    I use PTFE with adhesive dispensed on a roll. The adhesive allows placement for final "adjustment". But when shear forces...
  6. Replies
    20
    Views
    1,220

    The change in magnet flux has ruined the motor....

    The change in magnet flux has ruined the motor. Unless you can have engineered specs achieved in re magnification the torque/speed will surely be wrong.

    That's a lot of screwing around time which...
  7. I would recommend running a 70V line to speakers...

    I would recommend running a 70V line to speakers with volume controls to locations near where you want them heard. Then you can have a paging microphone and everything in one clean location.

    I...
  8. Replies
    5
    Views
    753

    You want to get a P Touch label maker and use the...

    You want to get a P Touch label maker and use the TZ tapes. Labels stand up to years of direct sunlight and I have use the clear tape with black letters to stick directly on the outdoor gauges. I...
  9. Look up anechoic and do the calculations for...

    Look up anechoic and do the calculations for sound absorption and reflection. You should be able to attenuate the higher decibel frequencies to a level comfortable for human hearing. Use C Filter...
  10. Replies
    30
    Views
    2,964

    Use a Chinese made inexpensive milling machine....

    Use a Chinese made inexpensive milling machine. They are cheap and can do a lot more than what you want a lathe to do quickly and cheaply machining coins. Use the milling machine to build the...
  11. Replies
    19
    Views
    1,452

    Drill a center hole for the size of the first...

    Drill a center hole for the size of the first step on the step drill. Then use a small drill and make lots of holes to get rid of excess material. Finally run the step drill all the way through. Use...
  12. Terrific job. Maurice T once told me as I was...

    Terrific job. Maurice T once told me as I was learning the trades, "do your work so it looks good, chances are if you go to that effort, it will work good too and pass inspection". I have always...
  13. Replies
    23
    Views
    7,465

    Alabama firewood How long a length are you...

    Alabama firewood

    How long a length are you looking for?
  14. I would contact your customer who has been so...

    I would contact your customer who has been so good to you and your company. Offer to give them all the supporting materials for their work. Let them decide who to continue to provide them the work. ...
  15. Replies
    45
    Views
    3,778

    If I can't buy with VISA / MC I ain't buying it ...

    If I can't buy with VISA / MC I ain't buying it

    I want the protection offered by the bank card

    Way too many scams and fraud

    Pay Pal user agreement is not for me
  16. Replies
    52
    Views
    4,390

    Oil mist in compressed air reacts to PVC piping...

    Oil mist in compressed air reacts to PVC piping which weakens the pipe. I have seen the result of the shattered pipe and how sharp the pieces are.

    Do not use it.
  17. Replies
    27
    Views
    2,884

    Gov used to offer seminars you could go to and...

    Gov used to offer seminars you could go to and learn the methods. The ones that will beat you blind are the female veterans 100% disabled non white mostly native Indian that speak Spanish. Then...
  18. Replies
    15
    Views
    1,625

    Greenlee knockout punches. Drill hole for the cap...

    Greenlee knockout punches. Drill hole for the cap screw, assemble the cutter, wind it through. Clean perfect holes, even square or rectangle. Or you can drill a hole, use a nibbler, and file to shape.
  19. Replies
    31
    Views
    4,092

    I would go one step further, find a good person...

    I would go one step further, find a good person who likes them and wants to give them a good home. Give them away. Merry Christmas
  20. Typically a variance of 10-20% is acceptable for...

    Typically a variance of 10-20% is acceptable for circuits like shown in Step 7, also the voltage driven frequency circuit is going to have some input protection from over voltage.

    What concerns me...
  21. Got hit hard enough to damage Was installed...

    Got hit hard enough to damage

    Was installed with uneven force on supports and damaged by hit or temperature changes

    Absorbed a chemical that deteriorated it caused the damage

    I would not...
  22. Replies
    19
    Views
    1,903

    They look like really old hip replacement tools...

    They look like really old hip replacement tools from a surgical kit.
  23. Replies
    2
    Views
    591

    Is it plugged in? Is the power coming in Ok? ...

    Is it plugged in?

    Is the power coming in Ok?

    Is power reaching the device?

    What is the operating voltage of each power supply?

    Are all safety interlocks operating (and not bypassed with a...
  24. Replies
    28
    Views
    1,331

    Have you contacted the steel supplier? I did a...

    Have you contacted the steel supplier?

    I did a search and came up with

    High Speed Steel | D2 Steel | D2 Technical Data

    for D2 steel

    If you call the supplier and ask they can provide...
  25. Replies
    7
    Views
    720

    and probably less rude comments from hateful...

    and probably less rude comments from hateful people with someone else spit in their coffee

    :willy_nilly:
Results 1 to 25 of 325
Page 1 of 13 1 2 3 4