Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: spirous

Search: Search took 0.00 seconds.

  1. the motor is finally working

    It's been a while now, but since i finally got my built to work, i thought of it as proper to report back here and have the thread as solved.

    So, i went with the Santerno Sinus N 0003 choice,...
  2. The new motor winding can be set externally to...

    The new motor winding can be set externally to 380volt star or 220 delta by altering the plates position.

    I dont know if i will need the full 2hp of the motor, but it is not a really big price...
  3. 243777243778243779 So, i received the motor...

    243777243778243779

    So, i received the motor rewinded for high speed, approximately 2800rpm. I tried again to have it run with the AB vfd, but no luck. So i m going to buy one, probably of the...
  4. thanks for the reply johansen, I asked the...

    thanks for the reply johansen,
    I asked the technician if it would be possible to simply pull out the 12 wires of the motor in order to do a simple modification, but he replied that the wires are...
  5. I thought my question would be simple for someone...

    I thought my question would be simple for someone with lathes and vfd experience, but maybe it was not clear enough or the thread is considered too old. I will try again to ask my question clearly,...
  6. It's been a while with this project. I was not...

    It's been a while with this project. I was not able to drive the motor with the AB vfd, so i took the whole motor and gearbox assembly to a motor rewiring professional in order to rewire it to for a...
  7. It could be possible to replace completely the...

    It could be possible to replace completely the motor,
    but i would then need to find one that fits good in the case where it is placed below the gearbox, have an axis that extends the correct amount,...
  8. If i understand correctly, there is a bank of dc...

    If i understand correctly, there is a bank of dc bus capacitors of 8 pieces of 260μF 400WV capacitors. The big ones shown in the photo.
    235879

    On the same board an LED bus charged is placed,...
  9. If i would go with a setup like this, why...

    If i would go with a setup like this, why wouldn't i go for a 380V vfd or transformer instead of 480, since the motor is 380?
  10. Thank you for your replies, The ebay shop...

    Thank you for your replies,

    The ebay shop suggested looks like it could have exactly what i could use, but for a 2hp unit, i would need to spend more than 500 euros, which kinda exceeds my margin....
  11. Here i attach the pictures again. ...

    Here i attach the pictures again.

    Unfortunately, i do not have a schematic of the motor and by looking online for more info, i couldn't find something helpful. At the front side of the motor,...
  12. thanks for the reply JST. Here is a picture of...

    thanks for the reply JST.

    Here is a picture of the wires where you suggest.

    234808

    There are 6 wires, plus the ground seven. It is a two speed motor though. I am not sure how this would...
  13. i would like 230VAC 1ph, to drive 380VAC 3ph simonet motor, with vfd

    Hi,

    I am wondering for quite some time now, how i will be able to run the simonet motor, of my schaublin/simonet 102 hybrid lathe. The motor is a 380VAC, three phase motor, and it is not possible...
  14. Replies
    22
    Views
    7,347

    And they' re not dirty cheap as i would thing....

    And they' re not dirty cheap as i would thing. The cheapest vernier is for 22,5 usd, after their 50% discount. Seems like a lot of instruments could be fakes after all. Wouldn't these companies being...
  15. Replies
    0
    Views
    492

    looking for simonet tailstock part

    Trying to eliminate/minimize the play of tailstock's center on my new old schaublin-simonet 102 lathe 180156, i find a "key-nut" having a cracked hole edge 180158. I contacted schaublin which is an...
  16. Replies
    22
    Views
    7,347

    Mmm, thank you for your replies! So you think...

    Mmm, thank you for your replies!
    So you think it's a fake. Could be.. I' ll continue my research. I was able to see in person a Mitutoyo and an insize one. I don't want a digital. And sylvac offers...
  17. Replies
    22
    Views
    7,347

    Is it an original mitutoyo vernier caliper?

    Greetings to the biggest machinist community,

    I join you today as a sequel of the possession of my new toy, a schaublin-simonet 102 lathe.
    One,of the many, important things you have to consider...
Results 1 to 17 of 17