Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: RC Mech

Page 1 of 42 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    118
    Views
    18,614

    Don’t count on it. Going on nearly a year since...

    Don’t count on it. Going on nearly a year since the build started.
  2. OP’s describing a lift where the objective is to...

    OP’s describing a lift where the objective is to unload a trailer which is then driven out from under the load.
  3. OT: Is that tongue in cheek? Typically run into...

    OT: Is that tongue in cheek? Typically run into this, owners tripping over dollars to pick up pennies.
  4. Replies
    31
    Views
    4,168

    That's fantastic- I can do both and far more,...

    That's fantastic- I can do both and far more, have more BS to deal with at the day job which would make the move to PA worth it for that type of work. With the understanding that may not be able to...
  5. Replies
    31
    Views
    4,168

    I’m not a machinist- that decision was made long...

    I’m not a machinist- that decision was made long ago. “Average” wage for a machinist in this country is little more than the poverty line. The gentleman above mentioned being an engineer and never...
  6. Replies
    31
    Views
    4,168

    TL;I didn’t Read: You have a mediocre job and you...

    TL;I didn’t Read: You have a mediocre job and you want to become a machinist? Talk about a lateral move.
  7. Thermal/overload relay. Between contactor and...

    Thermal/overload relay. Between contactor and motor, prevents motor from starting again if amperage draw was too high.
  8. Haas Fanboy identified. Never said there was...

    Haas Fanboy identified. Never said there was anything inherently wrong with their mills, but their TL lathes suck. Fanboys will fawn over everything they produce though- emotion clouds judgement that...
  9. Haas TL lathes suck. Gimmicky anodized...

    Haas TL lathes suck. Gimmicky anodized Al/hammertone painted handwheels that are great for whacking the operator in the delicate bits. Tailstocks are a joke. They must have UHMW gibs because the...
  10. Replies
    17
    Views
    1,224

    We were on the 401 this afternoon as well. Tool...

    We were on the 401 this afternoon as well. Tool in the Golf was probably riding the SUV’s butt, in the slow lane no less, and got brake checked. Hopefully Golf’s insurance sees it as a single-vehicle...
  11. Replies
    45
    Views
    4,955

    Long term relationships? Kickbacks to...

    Long term relationships? Kickbacks to purchasers/shippers? Customers that are as incompetent as they are?

    Tons of businesses still open in spite of themselves. Makes you wonder how badly you need...
  12. Replies
    63
    Views
    5,534

    Odd that everyone is jumping on the laser...

    Odd that everyone is jumping on the laser bandwagon. You can get beautiful cuts with a high-def plasma. You’ll go through torch tips and piercing is always hard on a machine but if you have a good...
  13. Obligatory “everyone is a moron except me”...

    Obligatory “everyone is a moron except me” comments aside, it’s the front sensors, wiring or steering wheel clock spring as noted above that are the usual suspects.

    Same issue on the...
  14. If that’s the case, I see they’re still for sale....

    If that’s the case, I see they’re still for sale. I’ll give him the benefit of the doubt. Thank you.
  15. Replies
    17
    Views
    1,867

    I gotcha. :cool: The lathe in my link is IMO an...

    I gotcha. :cool: The lathe in my link is IMO an excellent deal for a business looking to purchase new. The large spindle bore and rapids are quite useful. Not a top-of-the-line machine by any means...
  16. Replies
    17
    Views
    1,867

    We have a version of this Taiwanese lathe: GMC...

    We have a version of this Taiwanese lathe:

    GMC GT-3280 Precision Gap Bed Lathe

    No affiliation with the dealer other than he was kind enough to give me a manual for ours. You can find slightly...
  17. Stan, did you purchase that Standard Modern...

    Stan, did you purchase that Standard Modern carcass for sale out of Erin? I'm curious about the seller. He had angle plates for sale and accepted my offer but I couldn't get an address out of him to...
  18. Replies
    11
    Views
    1,132

    Pretty anemic homework question if that's truly...

    Pretty anemic homework question if that's truly what it is.

    x2 on stating what you currently have. Have a roll of MIG wire and a few vise grips? You'll need a few more bits. The Devil's in the...
  19. Replies
    42
    Views
    4,563

    Then yank the servos off man! I was ready to do...

    Then yank the servos off man! I was ready to do that on our lowly VMC-15. Sometimes you'd just rather not d*ck with things to the point where making them convenient for you trumps all.
  20. Replies
    50
    Views
    5,608

    Ag2O, interesting proposal. Haven't read all...

    Ag2O, interesting proposal. Haven't read all replies but H2O2 is a metabolite for some baceteria, indeed, many organisms. It can be used as a oxidation AND reducing agent- the latter will 'bubble' O2...
  21. Some of us here actually use our tools to make a...

    Some of us here actually use our tools to make a living. There's no sense in using trash tooling and expecting it to produce a superior finish in any material within a reasonable amount of time. You...
  22. This is a guarantee. The OP mentions cheap and...

    This is a guarantee. The OP mentions cheap and Amazon. It's no mystery he's working with a POS tool. Try a real shell mill or facemill with inserts that are actually carbide and report back.
  23. Replies
    86
    Views
    5,216

    Over 48 hrs have elapsed...hopefully he's got it...

    Over 48 hrs have elapsed...hopefully he's got it off the skid by now. :cool:
  24. Thread: Gd&t question

    by RC Mech
    Replies
    18
    Views
    1,193

    When the part is free from the chuck does it taco...

    When the part is free from the chuck does it taco in half? I'd measure it exactly as you described. Jog in X, get TIR, index the spindle by hand to another position, jog in X etc. Jog the indicator...
  25. Replies
    18
    Views
    1,951

    Prehistoric, unsupported and with fantasy...

    Prehistoric, unsupported and with fantasy pricing. Not quite equivalent to a Fadal...
Results 1 to 25 of 1034
Page 1 of 42 1 2 3 4