Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: mach2

Page 1 of 41 1 2 3 4

Search: Search took 0.01 seconds.

  1. I have one of these in my garage waiting for the...

    I have one of these in my garage waiting for the time to fix it up. The Milwaukee fits your description. Mine has an original base. Whatever you get be sure it has accessories like the over ram and...
  2. OP said joist and that implies shorter spans....

    OP said joist and that implies shorter spans. Joists and trusses can be made with any steel sections you want. Thats what the engineers are for. Rod is easier to bend into truss webbing than angle....
  3. Use round bar for the diagonal shear webbing. It...

    Use round bar for the diagonal shear webbing. It will be a whole lot easier. Who is engineering this? Here in the US truss manufactures have licensed engineers to certify the design. Don’t take...
  4. Replies
    20
    Views
    1,419

    Naegle is right about the oil. Cast iron is...

    Naegle is right about the oil. Cast iron is porous and even if you wash the surface with detergent oil will migrate to the surface. If you use detergents be sure to thourly rinse with water( like...
  5. Replies
    5
    Views
    439

    The change gear spider can slip out of position...

    The change gear spider can slip out of position disengaging the spider gears. The bracket you are questioning supports the back end of the change gear spider giving to two points of support. As long...
  6. Replies
    37
    Views
    1,743

    There was a very nice green John Oder showed us a...

    There was a very nice green John Oder showed us a few years ago. Brush painted if I remember right. It was an easy on the eye antique color. I have seen the photo posted several times on PM but...
  7. Replies
    18
    Views
    1,572

    Email sent.

    Email sent.
  8. Replies
    18
    Views
    1,572

    $4000 is the very very top end. I have one for...

    $4000 is the very very top end. I have one for sale that has never been advertised but I am 800 miles from you. Mine is in very good condition. I acquired it from a local high school in 1995. I am...
  9. Strap it to the carriage of your lathe and bore...

    Strap it to the carriage of your lathe and bore it with a boring bar in a 4 jaw chuck.
  10. Replies
    5
    Views
    720

    Pose has been edited.

    Pose has been edited.
  11. Replies
    5
    Views
    720

    Color implies KOLee

    Color implies KOLee
  12. Replies
    26
    Views
    1,891

    Logan user here too. I’m the opposite, all my...

    Logan user here too. I’m the opposite, all my lathe cutting tools are HSS except the one boring bar that is positive rake. 3/8” HSS fit the AXA holders nicely. I also use 5/16, 1/4, and 1/2.

    A...
  13. Replies
    26
    Views
    1,891

    Plus one on the HSS. Most carbide inserts at...

    Plus one on the HSS. Most carbide inserts at negitive rake and designed for high HP, high speed machines. The South Bend 9 is neither.
  14. Replies
    25
    Views
    1,555

    I think McMaster Carr has it.

    I think McMaster Carr has it.
  15. Replies
    11
    Views
    1,205

    I also have a Phase II. Mine is axa piston style...

    I also have a Phase II. Mine is axa piston style on a 10” Logan and have been very satusfied. I recommend the wedge style though as it has become industry standard.
  16. In the USA concrete interior floor slabs are saw...

    In the USA concrete interior floor slabs are saw cut after the concrete has hardened but before full strength. Saw cutting is done in a pattern specified by the engineer to control cracking due to...
  17. Thread: compound tee nut

    by mach2
    Replies
    6
    Views
    860

    Size the blank in the 4 jaw chuck as you say....

    Size the blank in the 4 jaw chuck as you say. Make it the t- slot width x length equal the axa body width. Take the blank and turn the upper part of the t-nut round with diameter just small enough...
  18. Thread: Morse taper 4.5

    by mach2
    Replies
    7
    Views
    710

    Sometimes the internal taper can get nicked,...

    Sometimes the internal taper can get nicked, dinged, maybe a stubborn chip embeded, etc. After you check again insert the sleeve lightly and turn it, sometimes you can feel such an imperfection....
  19. Thread: Morse taper 4.5

    by mach2
    Replies
    7
    Views
    710

    Are you sure the runout isn’t the lathe, spindle...

    Are you sure the runout isn’t the lathe, spindle bore could have a burr or in need of a little clean up.
  20. I don’t mean to be sarcastic at all but without...

    I don’t mean to be sarcastic at all but without knowing what that is for I think you need to hire an engineer. There are way more questions in that diagram than guy wire loads.
  21. Replies
    2
    Views
    483

    If you can’t find a Rockwell I suggest an M-head....

    If you can’t find a Rockwell I suggest an M-head. The M- is just a little larger than the original Rockwell. I have an M in storage and honestly you will probably like the M better dispite it not...
  22. Replies
    2
    Views
    483

    I have a Rockwell 21-100 for sale. The mill is...

    I have a Rockwell 21-100 for sale. The mill is located in central Indiana. I will not part it out. It is single phase but I still have the original 3 phase motor with all switching and wiring removed...
  23. Replies
    9
    Views
    1,330

    You will need advise from someone who knows your...

    You will need advise from someone who knows your machine to help with gib removal. They differ by machine.
  24. Replies
    9
    Views
    1,330

    From the photo I notice two crank handles broken....

    From the photo I notice two crank handles broken. That and the machines scrap yard origins suggests it may have suffered a face plant or two. The slides could wedge tight from such a fall. I would...
  25. Replies
    19
    Views
    2,323

    Can we assume chuck mounted only and not...

    Can we assume chuck mounted only and not tailstock supported?
Results 1 to 25 of 1001
Page 1 of 41 1 2 3 4