Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: JohnEvans

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    4
    Views
    313

    Looks like a good paper weight!

    Looks like a good paper weight!
  2. Replies
    2
    Views
    207

    Take a look at a "TPG" 3XX or TPGB " box lable is...

    Take a look at a "TPG" 3XX or TPGB " box lable is shot,hard to read.
    Also try this linkhttp://www.carbidedepot.com/formulas-insert-d.htm
  3. Here in Phoenix with the limited tooling...

    Here in Phoenix with the limited tooling $1200-1800. Your area probably 800-100.
  4. Replies
    25
    Views
    812

    Easier yet bring the dogs in the house !

    Easier yet bring the dogs in the house !
  5. Replies
    26
    Views
    1,267

    Legal size Priority envelopes are also flat rate...

    Legal size Priority envelopes are also flat rate a bit more like .50 or so. I use them on occasion.
  6. Try tightening the 2 screws in the side of the...

    Try tightening the 2 screws in the side of the can ring. AFTER FIRST loosening the little locking screws. No one ever seems to lube that area and the ring will sooner or later wear into the...
  7. Pull the quill out of the TS and use a long drift...

    Pull the quill out of the TS and use a long drift .
  8. Replies
    9
    Views
    672

    I'll bet you $5 that they don't use base /clear !...

    I'll bet you $5 that they don't use base /clear ! Most likely a pressure pot/remote gun for production painting. Base/clear is a car makers rip off ,goes to shit in a few years . Cheaper to buy a new...
  9. Replies
    0
    Views
    218

    FS CPMT 3XX carbide inserts

    Sorting through things on a lazy Sunday and found a mixed bunch of new and used CPMT 3 series inserts. Funny thing is I do not have any holders to use these. As I said some new and all the used seem...
  10. That ONLY works with keyed style chucks!

    That ONLY works with keyed style chucks!
  11. Too big a tip? filler size? Tip size #1 3/32...

    Too big a tip? filler size? Tip size #1 3/32 filler. Not all that bad but to me too much heat,fillet weld like that is one of the hardest to do.
  12. From the looks of that A arm more like a complete...

    From the looks of that A arm more like a complete new one would be in order. But as above weld in a repair taper sleeve. Fabricated piece with broken welds Sheesh !
  13. Replies
    15
    Views
    1,513

    Interesting ! spindle OD is smaller than I would...

    Interesting ! spindle OD is smaller than I would expect. Anyway lathe looks very nice,have fun.
  14. Replies
    15
    Views
    1,513

    And the question is ? What does that bloody great...

    And the question is ? What does that bloody great hole in the end of the spindle measure ? Looks to be 1-3/8s + .IF so someone has put a Heavy 10 spindle in this lathe,which is great!
  15. Replies
    16
    Views
    1,303

    Looks like a CNCed plain old semi-useless...

    Looks like a CNCed plain old semi-useless drill/mill to me. You can not make a silk purse out of a sows ear. Have the seller run a program on it,see how accurate/usuable it is/ain't.
  16. Any chance of putting a Heli-Coil in that plate ?...

    Any chance of putting a Heli-Coil in that plate ? Very nice work !
  17. Replies
    2
    Views
    571

    2-J vari speed head looks like 42" table ,mid 70s...

    2-J vari speed head looks like 42" table ,mid 70s or earlier with the door in the column.
  18. If you want to make things buy the Le Blond ! If...

    If you want to make things buy the Le Blond ! If you want a long term project get the 10EE. A few years ago a local dealer had a VFD repowered 10EE and he had a hard time selling it. With the...
  19. Replies
    169
    Views
    17,322

    If several of you people would have read the last...

    If several of you people would have read the last page or so you you would have seen Matt graduated several weeks ago. thread was started in 2013!
  20. Replies
    25
    Views
    1,788

    Well going by that BIG bore in the spindle I...

    Well going by that BIG bore in the spindle I would 10L aka Heavy 10. Only downside is the rather short bed,but for most work not a issue.
  21. The mill looks reasonable ,but as with any...

    The mill looks reasonable ,but as with any machine tool wear is the deciding factor. Parts for this will be few compaired to a Bridgeport.
  22. Yep the Le Blond is the one ,you will never...

    Yep the Le Blond is the one ,you will never regret having more C-C distance . Think MC fork tubes !
  23. Replies
    45
    Views
    3,551

    Yep ! And that is why I never ask any of my...

    Yep ! And that is why I never ask any of my buyers to do F&F . And I rather than doing F&F if the seller wants that I will add money on my end to cover the fees for MY protection! To me Paypal fee's...
  24. Replies
    45
    Views
    3,551

    Buyers paying with PayPal please note !

    If you purchase something using Paypal note that if you are being a nice guy cover the fees using Friends & family Paypal does not show your address for shipping ! And if your profile does not...
  25. Replies
    2
    Views
    708

    PM coming your way

    PM coming your way
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4