Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: mmarquette

Page 1 of 10 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    15
    Views
    1,216

    How do they compare to the originals in hardness....

    How do they compare to the originals in hardness. Could also intentionally sacrifice one to see what it will hold up to and see if it fails or deforms above what you both feel good with.
  2. Replies
    23
    Views
    2,630

    For 250 still like it.

    For 250 still like it.
  3. Replies
    23
    Views
    2,630

    Its on the CL ad. Says 1$. id get it if had room.

    Its on the CL ad. Says 1$. id get it if had room.
  4. Replies
    37
    Views
    2,473

    I havent spent 1000$ with them over 4 years....

    I havent spent 1000$ with them over 4 years. While back i called and needed to find some screws and clamps for some misc. borng bars got on Ebay. Called up and they spent the time to identify and get...
  5. I like ink on eyepieces. Simple ,funny, doesnt...

    I like ink on eyepieces. Simple ,funny, doesnt hurt or scare anyone. Best is if everyone else is in on it you can just let em walk around like that and hopefully they will leave with it to show...
  6. Replies
    54
    Views
    3,829

    Found a 6 jaw set true cheap. Bought it. After...

    Found a 6 jaw set true cheap. Bought it. After running it found i could not grip stock tight enough for semi roughing. Took 3 jaws out.
  7. Just got one couple months ago. Same thing no...

    Just got one couple months ago. Same thing no name. Looks like its an Ellis.
  8. Replies
    14
    Views
    4,829

    Heard from beans. I dont eat em so mine must come...

    Heard from beans. I dont eat em so mine must come from something else.
  9. Maybe switch to short bolts??? I like the low...

    Maybe switch to short bolts??? I like the low profile of setscrew too but if its that annoying would be a solution
  10. I made some for my DA sized Aloris sty;e. Used...

    I made some for my DA sized Aloris sty;e. Used 1018 2x6 inch bar. It was also something i had on hand. Made sure there was plenty under the cutter when i milled the slot . Using on a 10 hp 24"...
  11. Replies
    43
    Views
    4,243

    Shaper can do some other stuff like dovetails....

    Shaper can do some other stuff like dovetails. But arbor press does alot of other pressing duties . I have 16" and did some keyways. Didnt have to make a special broch plug for a 1 off project. Has...
  12. Replies
    17
    Views
    1,931

    Even better! should even seal with some grease....

    Even better! should even seal with some grease. You know how nasty that tape gets around oil.
  13. Replies
    17
    Views
    1,931

    Wonder if fafnir could tell you by volume for...

    Wonder if fafnir could tell you by volume for that part number. I know how i would do if i needed to and wanted to keep it as close to 30 percent. fill 100 percent of empty space 30 percent around ....
  14. Iusually just thread an appropriate size piece of...

    Iusually just thread an appropriate size piece of round stock. in your case 3" or a little less. Then put into the right sized hole in a 1/2 or 3/4 plate .Weld it in and face the front back off to...
  15. Replies
    15
    Views
    2,228

    Thanks for posting . It helped identify the one i...

    Thanks for posting . It helped identify the one i picked up awhile ago. Old and crusty was not able to find name till i saw where it was at on yours. So small on mine had to use a eye loupe to see....
  16. Replies
    14
    Views
    1,622

    I agree used to do just compression tests but...

    I agree used to do just compression tests but then started doing the leak down test. Compression tests can vary with battery charge starter age ect. Have done both on the same engine. While the...
  17. Replies
    19
    Views
    5,499

    Thanks for reposting pictures. Remends me to...

    Thanks for reposting pictures. Remends me to think more on how to get a job done with what i have. Would like to see a photo gallery of your shop and or jobs you have done.Be great if all photos...
  18. I might have missed it but can you imagine the...

    I might have missed it but can you imagine the sticker price of this thing. The new ones are double what my 92 Dodge diesel was.
  19. I think you should move to finding some more of...

    I think you should move to finding some more of your own work instead of being a sub. That sub work is still really there work not yours.
  20. Im partial to Hendeys but usually find them much...

    Im partial to Hendeys but usually find them much cheaper. Your getting ALOT more in the LeBlond. Find the room you will not regret it
  21. Replies
    16
    Views
    2,015

    Mine is almost identical. Really like it. But...

    Mine is almost identical. Really like it. But mine has vertical head . Knowing what i know now of machine i would be willing to make it work if i needed another
  22. I have the same mill. My upper slide is all the...

    I have the same mill. My upper slide is all the way up against the vertical head. still has slight gap if i remember right. Im gussing they made the block to close it up. All the others ive seen...
  23. Replies
    5
    Views
    830

    Saw there auction near me in versailes . Big...

    Saw there auction near me in versailes . Big problem is getting it out. No set loading fee. Need alot of insurance and other credentials to get forklift in to get it
  24. Surprised there is not a 1 in front of the 8

    Surprised there is not a 1 in front of the 8
  25. Replies
    17
    Views
    2,286

    Id go after the Cisco lathe in Benton thats on...

    Id go after the Cisco lathe in Benton thats on CL. That foster is to specialized as many have said. No quick change gear box for threading for starters. Nice looking machine in great shape for sure ...
Results 1 to 25 of 234
Page 1 of 10 1 2 3 4