Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: kenscabs

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Don't machine them down, machine a vee groove and...

    Don't machine them down, machine a vee groove and use it as the tool block.
  2. Replies
    1
    Views
    890

    17/32" same thing (within a couple of tenths) . ...

    17/32" same thing (within a couple of tenths) . Available anywhere, check google i.e. Rockler stock no. 62069.
  3. Replies
    1
    Views
    284

    Unless there's a 120volt component in there,...

    Unless there's a 120volt component in there, there doesn't need to have a common. 2 hots and a ground.
  4. PM sent on Albrecht 0-1/8" chuck on sensitive...

    PM sent on Albrecht 0-1/8" chuck on sensitive arbor, looks new - $110.
  5. You're right they are. I've build my own 10hp...

    You're right they are. I've build my own 10hp for cheap but needed a 20hp asap a while back so I went with an American Rotary. Nothing but good things to say about it. I even called their Tech...
  6. Replies
    19
    Views
    2,281

    I learned a long time ago you need a thick skin...

    I learned a long time ago you need a thick skin on this site. Most of the time it's simply banter. Don't take stuff like this so seriously. The trick is to come back with some good sarcastic wit.
  7. Replies
    19
    Views
    2,281

    Is that $300 for each lot of 7?

    Is that $300 for each lot of 7?
  8. Replies
    21
    Views
    1,431

    So here's the number of conductors from Ugly's...

    So here's the number of conductors from Ugly's Electrical References: 1 1/4" PVC Sch 40, I'm assuming THHN 16-#8 11-#6 7-#4 6-#3 5-#2 3-#1. The size of the wire is going to be dependent on how much...
  9. Typical Rockwell/Delta parts, the shaft cost more...

    Typical Rockwell/Delta parts, the shaft cost more than the whole saw. Shaft [42631613] for Delta Power Tool | eReplacement Parts
  10. Replies
    12
    Views
    2,916

    If you're looking to move up to an 8" the only...

    If you're looking to move up to an 8" the only ones I'd consider (and I've had) are the Rockwell 8" wedgebed (1970s), the Delta DJ20, and my latest acquisition an older Powermatic 60 (8"). If you...
  11. mattrixx, my 6" part no. 905162 measures 36mm on...

    mattrixx, my 6" part no. 905162 measures 36mm on the inside. The 505-644 is an older model and you may have problem getting it.
  12. I plugged in a Mit part number for my 12" Mit....

    I plugged in a Mit part number for my 12" Mit. (901329) into Western supply part search and I get a result. Your Mit 505-644 may be part number 905162 which also comes up if it's 505-644-50, 505-644...
  13. I got a replacement crystal and bezel at Western...

    I got a replacement crystal and bezel at Western Tool Supply for my 12" Mit. Check with them. Better going into it with the part number. What is the outside diameter of the bezel?
  14. Don't know why "3hp max", seems cfm and psi are...

    Don't know why "3hp max", seems cfm and psi are the issue.
  15. 218908218909 Before and after. Made a new...

    218908218909

    Before and after. Made a new gasket and filled it with compressor oil. Remember, it was the principle of the thing. Runs smooth as silk.
  16. Little Giant uses a proprietary dielectric oil. ...

    Little Giant uses a proprietary dielectric oil. Told me oil filled pumps like these are disposable. Now I have to get it back together and running on principle alone. I'll grab some AC compressor...
  17. Well I've given up trying to post a photo. Keeps...

    Well I've given up trying to post a photo. Keeps uploading to nowhere. Anyway the tanks mfg. is Hurri-Kleen, looks like they're not around anymore. I'll just source a replacement.
  18. What oil to use in an oil filled solvent tank pump?

    Scored a parts washer off CL. I needed to replace the AC cord going into the pump. There hadn't been solvent in the unit for years so I was surprised when I took the pump apart and oil pour out...
  19. Replies
    12
    Views
    918

    Fleabay has cheap to rediculas priced 2-3/4"...

    Fleabay has cheap to rediculas priced 2-3/4" pillow bearings.
  20. Replies
    22
    Views
    3,127

    Yep, condensation would be the problem. ...

    Yep, condensation would be the problem. unpainted surfaces are prone to rust. Of course the obvious answer is to keep surfaces well oiled. What I was going to try this winter is to hang a 250 watt...
  21. No I think in the southern hemisphere.

    No I think in the southern hemisphere.
  22. Replies
    413
    Views
    55,975

    Great pics.

    Great pics.
  23. All sold. Thanks guys.

    All sold. Thanks guys.
  24. Chin Yu and Jacobs chucks sold. Entertaining...

    Chin Yu and Jacobs chucks sold. Entertaining offers on the Bison.
  25. Sorry. Cleared some space. Chin Yu and Jacobs...

    Sorry. Cleared some space. Chin Yu and Jacobs chucks sold pending payment.
Results 1 to 25 of 184
Page 1 of 8 1 2 3 4