Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: gwelo62

Page 1 of 7 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    21
    Views
    1,787

    I would agree on the mechanical side of new...

    I would agree on the mechanical side of new vehicles. It is the electronic everything else I fear.
  2. Replies
    21
    Views
    1,787

    I am going to ask 1750 and negotiate. I saw a...

    I am going to ask 1750 and negotiate. I saw a 2007 with 192000miles for 11 000. I buy cars on mileage not age.
  3. Replies
    21
    Views
    1,787

    No air and the heater core is rotten. I was going...

    No air and the heater core is rotten. I was going to get a new engine but my wife told me that was not happening! It has developed a new noise from the engine which I cannot ID, but it still runs...
  4. Replies
    21
    Views
    1,787

    OT - End of an Era!

    258437
    My 1992 Toyota pickup is being replaced! Hirohito's Revenge will be going to the Walmart car-park to be sold. 226 000 miles. She has been a fine truck.
  5. Replies
    94
    Views
    8,591

    Changing jobs seems to be the only way in all...

    Changing jobs seems to be the only way in all jobs these days. The HR people would rather pay a recruiting fee and a higher wage to your replacement than pay you to stay.
  6. Replies
    36
    Views
    3,115

    Sulzer has some big compressors. When I worked...

    Sulzer has some big compressors. When I worked for Sulzer in South Africa our sales engineer said you could tell who ran the business by the compressors - Engineers = Sulzer. Expensive upfront, cheap...
  7. Is the tip of the cutting tool At the same height...

    Is the tip of the cutting tool At the same height as the tip of the centre in the tailstock. Could explain poor finish.
  8. Replies
    28
    Views
    16,581

    I have tried contacting jayhawkman with a...

    I have tried contacting jayhawkman with a message. His mailbox is full. Is he still on the forum/alive?
  9. Replies
    30
    Views
    3,631

    I don't have an issue with the colour-scheme. It...

    I don't have an issue with the colour-scheme. It certainly wouldn't affect my decision to purchase. Pity I'm too far away.
  10. Replies
    21
    Views
    3,119

    It's very simple.It's easier. My previous...

    It's very simple.It's easier. My previous employer would not allow aluminium molds, only steel, but insisted on a 5 year payback - impossible. Oriental suppliers used aluminium. We shut down lines...
  11. Replies
    10
    Views
    1,417

    Getting a BP up and running

    I am looking at a 1966 BP j-head. It was taken from a maintenance shop and stored under an open lean-to. The motor runs. It is no jewel(gouges on table and surface rust). What is the minimum lifting...
  12. Thread: Proud Dad

    by gwelo62
    Replies
    7
    Views
    1,140

    Congratulations to both of you.

    Congratulations to both of you.
  13. There is a bit of a racket going on when it comes...

    There is a bit of a racket going on when it comes to new, large(mostly foreign)new factories being built in the US. Gordon announces he is looking for a site for his new factory. Various states and...
  14. Mr.OP, what is your status? Have you made a plan...

    Mr.OP, what is your status? Have you made a plan yet?
  15. I have been offered a J-head for $1200 or a...

    I have been offered a J-head for $1200 or a large old Jet mill/drill for not much less. It is not as good-looking as yours and probably more used. It comes from a bloke I trust so I am hoping that...
  16. Replies
    212
    Views
    13,509

    How different would it be if our equipment was...

    How different would it be if our equipment was priced the same as China or Russia? I read that the M16 replacement will cost the taxpayer $3000 each. The opposition spends most of its money on lots...
  17. Thread: Boeing 737 Max

    by gwelo62
    Replies
    843
    Views
    64,172

    If the manual overide is electronic, not...

    If the manual overide is electronic, not hydraulic or cables the fault may not be bypassable - assuming this plane is all fly-by-wire.
  18. Go buy a dedicated generator/motor set. IC...

    Go buy a dedicated generator/motor set. IC engines are made to run 'flat-out.' We throttle them for our vehicles. The generator and engine will be matched for each other to run as efficiently as...
  19. Replies
    19
    Views
    3,816

    Had a similar event over a car. Email...

    Had a similar event over a car. Email conversation claimed owner was being deployed Nebraska. Photo looked very "spanish" architecture in the background. Phoned and spoke to an Eastern European male....
  20. When I was an appie in the 80's, Connoly's in...

    When I was an appie in the 80's, Connoly's in Bulawayo had just got some NC machines. A bloke from Harare(at Bulawayo Tech) was programming at his employer. I assume Nimrs,Issels and the Harare...
  21. Replies
    14
    Views
    4,631

    Is OSHA going to allow line shafts?

    Is OSHA going to allow line shafts?
  22. Thread: Free Cad

    by gwelo62
    Replies
    10
    Views
    2,303

    I live in the US. I have used my child's college...

    I live in the US. I have used my child's college status to download an educational version of AutoCAD for use at home. However, I recently downloaded a drawing from a bathtub manufacturer. The...
  23. Replies
    31
    Views
    2,165

    Used Moore and Wrights are also worth a look.

    Used Moore and Wrights are also worth a look.
  24. All the best. Thanks for taking over, Cheers

    All the best. Thanks for taking over,
    Cheers
  25. Mr.Milacron. Any volunteers yet?

    Mr.Milacron. Any volunteers yet?
Results 1 to 25 of 172
Page 1 of 7 1 2 3 4