Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: mach2

Page 1 of 39 1 2 3 4

Search: Search took 0.03 seconds.

  1. And it can only be mailed?

    And it can only be mailed?
  2. Replies
    10
    Views
    566

    I don’t think you need the inverted v on the...

    I don’t think you need the inverted v on the riser. Mill a recess slot in the riser for the steady to fit in. Locate the steady on the riser as accurately as you can front to back then drill and ream...
  3. Replies
    17
    Views
    2,124

    Not fmiliar with Regals, I would also check fit...

    Not fmiliar with Regals, I would also check fit between the carriage and bed, saddle and compound etc. something bent and now rocking my cause irregular surface finish.
  4. Replies
    11
    Views
    759

    You will find serial numbers and model numbers...

    You will find serial numbers and model numbers here and a lot of very useful Logan information. Including how your lathe was originally configured.

    Logan FAQs
  5. Replies
    11
    Views
    759

    Here is the 210: Logan Engineering Co. -...

    Here is the 210:

    Logan Engineering Co. - Publication Reprints - Model 210 Back Geared Screw Cutting Lathe | VintageMachinery.org

    They were along with the Wards equivelant very popular. The...
  6. Replies
    32
    Views
    2,221

    Looks to me like the orange pad does not move....

    Looks to me like the orange pad does not move. The smaller pad above is what moves when the screw is turned.
  7. Replies
    32
    Views
    2,221

    I have a millrite on levelers. I like it level. I...

    I have a millrite on levelers. I like it level. I made a pad from 2 layers of 3/4” plywood. The levelers have long stems through the plywood pad and mill base casting. Nuts and large washers top and...
  8. Replies
    14
    Views
    1,235

    I’ve been using led bulbs in these with much...

    I’ve been using led bulbs in these with much improved lighting
  9. Replies
    14
    Views
    1,235

    My favorite: Search Results for “Light” –...

    My favorite:

    Search Results for “Light” – Moffatt Products
  10. Replies
    51
    Views
    4,891

    The clamps ar another of my favorites. What you...

    The clamps ar another of my favorites. What you should be looking for in his videos ar the methods like drawing on the stock with chalk. The designs also follow the shape of his tooling.
  11. Replies
    51
    Views
    4,891

    Look up raymond menendez el metal on YouTube. He...

    Look up raymond menendez el metal on YouTube. He has been mentioned several times here. Just yesterday he posted a new video on making a height gage. My favorite of his is a machinist level , even...
  12. Replies
    19
    Views
    1,735

    Burke sold a small vise for their horizontal...

    Burke sold a small vise for their horizontal mills and it was quite common. Good to orientate the jaws perpendicular to the cutter though. Go with a small machinist vise I hear the import quality is...
  13. Hope steel windows will have glazing stops sized...

    Hope steel windows will have glazing stops sized for insulated glass. Most any steel window manufacturer will too. However, steel windows came long before insulated glass so those stops are a...
  14. Replies
    9
    Views
    2,113

    And still supported by Logan Actuator. Lots of...

    And still supported by Logan Actuator. Lots of used parts available and most standard aftermarket accessories can work on it. Many are in good shape too. My Logan’s are 10” and will take up to 1/2”...
  15. Replies
    34
    Views
    2,638

    And are the gibs properly adjusted?

    And are the gibs properly adjusted?
  16. Replies
    34
    Views
    2,638

    I’m not that knolegable on the Bridgeport mills...

    I’m not that knolegable on the Bridgeport mills but I did have a similar problem with a Millrite mill. First check as already mentioned for a bent feed screw by removing it and rolling it on a flat...
  17. Once the bore is close I use blue dye and a...

    Once the bore is close I use blue dye and a scraper to fine tune the fit.
  18. I agree with 10k for the most part. My best chuck...

    I agree with 10k for the most part. My best chuck is a 5” from Enco. It turns .003 at 6”, about the best you can to with an inexpensive chuck.

    I think your problem is partially in the backplate....
  19. Thread: Logan lathe

    by mach2
    Replies
    66
    Views
    3,374

    I hope one of those books is a Logan owners...

    I hope one of those books is a Logan owners manual. What each of the controls does is covered in very simple English, recommended in post #2. It took 50 posts here to get through.
  20. Post deleted

    Post deleted
  21. You have quite a bit there. It is very hard to...

    You have quite a bit there. It is very hard to tell all you have because much is covered up. Photos are a good start though. Your best prices will come from understanding exactly what you have....
  22. Thread: Logan lathe

    by mach2
    Replies
    66
    Views
    3,374

    The bushing is keyed to the gear and turns with...

    The bushing is keyed to the gear and turns with it. The wear will be between bushing and 60 Rockwell stud. The stud being harder than the bushing prevents galling. The bushing is oilite bronze and...
  23. Thread: Logan lathe

    by mach2
    Replies
    66
    Views
    3,374

    The gear plate photo is difficult to read. Can...

    The gear plate photo is difficult to read. Can you post a better photo or list the numbers in the stud gear column? The QC gearbox appears the same as that used on the 10 and inch Logan lathes, the...
  24. Replies
    12
    Views
    1,233

    The spindle thread should be 1 1/2”-8 and if it...

    The spindle thread should be 1 1/2”-8 and if it the chuck screws on ok then what the others have said. Either there is a second set of outside jaws or the jaws are reversible. If the jaws are...
  25. Replies
    12
    Views
    1,233

    Are you saying the chuck does not fit your lathe?...

    Are you saying the chuck does not fit your lathe? Or just that it too small to hold the work?
Results 1 to 25 of 968
Page 1 of 39 1 2 3 4