Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: johnoder

Page 1 of 60 1 2 3 4

Search: Search took 0.38 seconds; generated 12 minute(s) ago.

  1. Universals are lighter than Plains, smaller...

    Universals are lighter than Plains, smaller everything like wheel and wheel head

    My ''47 14 X 60 B&S is less than 7000 - 14" wheel max

    Add 3000 for Landis extra length and good sense and call...
  2. Replies
    7
    Views
    363

    Thread pitch gages are not expensive

    Thread pitch gages are not expensive
  3. Replies
    3
    Views
    273

    If you buy a new one maybe it will never miss a...

    If you buy a new one maybe it will never miss a beat in 15 years - like mine. The sizeable first cost turns out to be practically nothing spread out over that length of time
  4. Indeed- and it turns out to be "self gaging" as...

    Indeed- and it turns out to be "self gaging" as to how much to file off the pins

    put in pins, reassemble (if disassembled) and turn back gears past the repair - and of course at first it stops...
  5. Back gear ratio is 7.8 to 1. I'd be fixing the...

    Back gear ratio is 7.8 to 1. I'd be fixing the back gear - just like I did over 50 years ago on a 13" SB

    Info on your lathe in here

    Precision tools : Pratt & Whitney Company : Free Download,...
  6. Spec sheet says hole is 1 5/16. 1" pipe is very...

    Spec sheet says hole is 1 5/16. 1" pipe is very near to that. Seems doubtful on the MT5 - since it is 1.75 big end - and the spindle nose thread is but 2 1/8 - 8

    Also states collet capacity is...
  7. If you look on the first real page of the manual...

    If you look on the first real page of the manual (the one after GS10) you will see it applies only to 2A and 4A serials
  8. Replies
    3
    Views
    366

    Check your email

    Check your email
  9. Spec Page from Catalog 33 - geared head down the...

    Spec Page from Catalog 33 - geared head down the page. Says the 12" pulley was 6"

    302123

    And a crop of the 12" geared head stuff

    302124

    A bit up from this crop it says the 12" lathe...
  10. Replies
    5
    Views
    349

    Something wrong there with the 21/32 - which is...

    Something wrong there with the 21/32 - which is .656"

    You add 2 to the 28 and get 30, and 30 divided by .656 = not quite 46 DP

    An 18DP 28 tooth will be 1.667" OD
  11. Richmaccarty last visited forum over 6 years ago

    Richmaccarty last visited forum over 6 years ago
  12. Replies
    69
    Views
    17,998

    Lot of 15 verticals completed December 1953

    Lot of 15 verticals completed December 1953
  13. Some scans from Catalog 33 in that area ...

    Some scans from Catalog 33 in that area

    302046302047
  14. Replies
    10
    Views
    2,187

    See page 7 of 35 here. Though not listed on the...

    See page 7 of 35 here. Though not listed on the QC box, if you have the 48T stud gear installed (instead of the 24), it will definitely cut 14 in the 28 position
    ...
  15. L&S was a firm believer in belt wrap and freely...

    L&S was a firm believer in belt wrap and freely used idlers on flat belt drives

    302040
  16. Posting photos will help folks have an idea of...

    Posting photos will help folks have an idea of what your are trying to do. Good info here on posting them.
    ...
  17. Replies
    2
    Views
    228

    Looks like 30 minutes here - no slow cool (click...

    Looks like 30 minutes here - no slow cool (click on image to enlarge)

    heat treating 17-4 ph to h900 condition - Bing

    have fun
  18. Replies
    6
    Views
    272

    My 22" CM s/n 4742 I owned briefly 35 years ago...

    My 22" CM s/n 4742 I owned briefly 35 years ago did not have hard ways (none the less, Reed Roller Bit here in Houston paid 20K to have it rebuilt in 1979, then gave it away to me for $2.5K)

    My...
  19. Replies
    12
    Views
    983

    I wish I could unearth the picture I used to have...

    I wish I could unearth the picture I used to have showing a lathe marked D&E but attributed to ATW:D
  20. Thread: Hendey 16x6

    by johnoder
    Replies
    20
    Views
    875

    Cone heads are in the late thirties catalog, and...

    Cone heads are in the late thirties catalog, and "Constant Velocity" machines first appeared in the early teens with the 8 speed gear head - representing at least a 20 year overlap
  21. Replies
    12
    Views
    983

    My understanding is that Mr. Egan came after Mr....

    My understanding is that Mr. Egan came after Mr. Lodge - and D&E morphed into American Tool Works

    The lead screw not shown in Post #1 will be found residing INSIDE the bed
  22. Thread: Hendey 16x6

    by johnoder
    Replies
    20
    Views
    875

    Real early 12 speed - plain spindle bearing,...

    Real early 12 speed - plain spindle bearing, threaded spindle nose - both these features standard options until early years of WW2

    The 16 of those days only went to 382 top spindle speed
    ...
  23. Replies
    38
    Views
    12,907

    Serial book goes back to 1936 and 100114 - so...

    Serial book goes back to 1936 and 100114 - so yours is a bit older

    A very good way to get folks talking about your lathe is to start your own dedicated "thread"

    I made a little scan / screen...
  24. Good info here if you can find a copy - the...

    Good info here if you can find a copy - the maintenance section includes scraping lock nut faces for actual squareness

    301805
  25. Replies
    5
    Views
    660

    Transmission compliments of Model A Ford

    Transmission compliments of Model A Ford
Results 1 to 25 of 1496
Page 1 of 60 1 2 3 4