Search:

Collets sold pending.

The second is a parts chuck. I’m not sure what is going on with it, but the hand wheel ring gear seems over size for the small double gears. Look at the first picture in this post. I have the...

OK it's really only 1 and a parts chuck. They are both 2J A2-5 spindle mounts.
The first is in good shape. It's the large handwheel type, marked not to exceed 4000 rpm.
$275 for the chuck plus...

OK Joe, I had to find out. I took the chuck apart and there are no repairs, in fact the inside looks very nice. 1st pic.

John, I have an old 5" Skinner that sounds like yours. I've never had it...

Joe, I'm not sure what you mean by the 1st chuck being burst.
It's in good shape except for the cut around the front circumference.
Pics in 2nd and 3rd post are the damaged 2nd chuck

Damaged gear.

Pictures of second chuck.
Next post is damaged gear.

Greg, delete this if you don't want for sale items here, but these chucks are old enough most PMer's will have no interest in them over in the F/S section. The first came on an old Sebastian treadle...

Sold pending.

I have a few Sjogren-Hardinge speed chucks and I always thought the small handwheel, 7 3/4", were the high speed chucks as used on the 10EE. But one is a A2-5 mount with a 10" handwheel and it's...

I bought this back plate years ago but never used it.
It needs to be fit to your chuck. 8" OD, 2 3/8" - 6 tpi thread.
See pics for other dimensions.

$65 plus shipping in medium flat rate box.

I posted a couple for sale a week or so back.
Maybe they'll be closer to what you need.

A couple of steadies and a follow rest for sale.

This is on CL. How much does it weigh? I don't have room for it, just curious.
Looks complete with vise and table support.
Around what year would this be from?
He was asking $400 then a few hours...

I meant to post this a while back. I have a 320 lb. Fisher and it's about 31.5" long. I can't see the pictures anymore but if I remember right the anvil in the auction was some inches longer. 500...

The second steadyrest is for about a 14” swing lathe. Again I’m not sure what it really went to. It’s about 7” from the center of the 3 3/16” ID center hole to the top of the “Vee”on the ways. Just...

A few more pics of the same set.

I'm putting these here in Antiques because they're fairly old. The first one with the follow rest is for I think a 16" swing lathe. It has a short leg on the bottom bearing surface opposite the...

By all means.
Welcome back.
I'll also add no one knows how they would react in any given situation until it happened to them.
No explanation needed here.

Here's the whole forge.
The pan didn't come with it.
I picked that up somewhere else.

I had a forge like that I sold a few years back. Interesting motor.
I never had it running but the guy that bought it rewired it and said it ran well.

My wife and I are big Red Sox fans. The crowd noise is so loud it's very hard to hear the announcers.
More so on a nationally televised game. Very annoying.
Now I have to go outside and tell those...

I'm helping a family sell an estate. It's down to just a few machines.
The Mattison was in a storage room with wood piled all over and around it.
I just want to verify it works as it should before...

What got me thinking about the cold was I just picked up a P&W model C lathe and I'm storing it in my barn for now.
It had been sitting for a long time and is very dirty and gunked up. The controls...

Thanks for the replies Richard and Stephen. A good point about the lumber yards.

I need to check out the operation of a big Mattison 202 rip saw. My question is, will running it in the cold damage anything?
It's in a unheated shop and it's been getting down to near zero at night...