Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: CosmosK

Page 1 of 29 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    33
    Views
    1,960

    When's the last time you visited? Lots has...

    When's the last time you visited? Lots has changed. In 3.5 years I've only ever seen one other person open carrying ;)

    I talked to a couple people who have visited Titan's new shop here north of...
  2. Replies
    28
    Views
    1,566

    If you are talking quantities of up to 1000, I'd...

    If you are talking quantities of up to 1000, I'd be really surprised if you can't beat your vendor. Check out a Speedio. Cycle time will be fast. Those machines, with the right work in front of...
  3. Replies
    8
    Views
    366

    Yes, output is 208 Wye. Input is delta. The...

    Yes, output is 208 Wye. Input is delta. The neutral went to the center of the output to get them all to be 208 to ground. Without, they were a few volts off and the Speedio could tell.


    ...
  4. Replies
    8
    Views
    366

    Neutral awg size for Auto transformer

    I have a transformer for my new Doosan lathe. Ellison sold me an autotransformer to get the 3 phase 240 delta I have down to 220.

    My speedio uses an isolation transformer and the X0 had to be...
  5. Sentry does. The bank needs that to protect...

    Sentry does. The bank needs that to protect their collateral from you (and me) ;)
  6. Beats being dead in the water though ;) Good luck

    Beats being dead in the water though ;) Good luck
  7. I financed my first machine with Banterra. I...

    I financed my first machine with Banterra. I paid for insurance through them for the first few months. It was maybe $45/mo. At the time, I had basic commercial liability insurance I needed to...
  8. Replies
    12
    Views
    1,019

    I started making my own parts on a cnc router as...

    I started making my own parts on a cnc router as well. I was looking at the 30k range too. I was going to get a Hass Mini Mill, but ended up financing a Speedio. Zero regrets. I wanted new to...
  9. I use Orange vises and the shortest tools I run...

    I use Orange vises and the shortest tools I run can reach the top of the vises so I haven't found the need for risers. Occasionally I'll have to set a tool up to stick out a little more, but it's...
  10. Replies
    10
    Views
    877

    I had a Royal for a while mounted on top of my...

    I had a Royal for a while mounted on top of my mill. I got rid of it in favor of vent fans. The mist collector was not quiet so cut down on me being able to hear what was going on inside the...
  11. Replies
    112
    Views
    7,871

    Here it is ready to show the wife. I told her I...

    Here it is ready to show the wife. I told her I was buying something for "us" ;)

    318101
  12. Replies
    112
    Views
    7,871

    The older machines have a 10.5" screen. They are...

    The older machines have a 10.5" screen. They are transitioning to 15" with touchscreen. I believe it has to do with the control version, Fanuc Oi-TF Plus is the new control. Yes, it has I-Guide. ...
  13. Replies
    112
    Views
    7,871

    Thanks. I can't wait to get it running. Entry...

    Thanks. I can't wait to get it running.

    Entry level Takisawa had a chip conveyor standard which was nice.

    Doosan had the following (Tak did not):
    -conversational (important for me)
    -tool...
  14. Replies
    112
    Views
    7,871

    The lathe arrived this morning into my new shop...

    The lathe arrived this morning into my new shop location. The landlord/neighbor are making me move into another unit. I opted for a smaller space, so it's going to be cozy. I was expecting no...
  15. Awesome, thanks Frank. While we're on the...

    Awesome, thanks Frank.

    While we're on the subject, is there a way to add a button into the feed hold loop? I'd like to be able to put the machine in feedhold from another source besides opening...
  16. Replies
    8
    Views
    802

    I'm not sure if you have the little tank or the...

    I'm not sure if you have the little tank or the bigger one (35 gal or so). I've used both. 24" or space behind it might be fine for either. On the little one, the casters don't swivel, they only...
  17. Frank, the manual left me wondering still, so I...

    Frank, the manual left me wondering still, so I asked here.

    So, can you give me a similar explanation for the NPN outputs? Is P normally high (+24) and the go low(same as N) when the output is...
  18. So, is the the P terminal at +24 and the N...

    So, is the the P terminal at +24 and the N terminal the input?

    Wire from P to sensor, output of sensor goes to N. I'm going to use a relay so I'd effectively by jumping the P to the N to trigger...
  19. Replies
    76
    Views
    5,393

    I'm not seeing any hate in this thread, just...

    I'm not seeing any hate in this thread, just people doing the public service of trying to help someone else getting burned. Gossip have been around for millennia and serves a crucial role in...
  20. I'm a little confused by the I/O layout. For the...

    I'm a little confused by the I/O layout. For the PNP inputs, to trigger the input would you effectively jumper the N and P terminals for the input? I'm used the the N being COM(ground) and it being...
  21. Replies
    76
    Views
    5,393

    If you click on the post number, the url will...

    If you click on the post number, the url will change and the link will direct you to that post.

    page 13 or so:
    ...
  22. Midwest will sit on your order for a solid week. ...

    Midwest will sit on your order for a solid week. I had a couple that didn't arrive until a week or two after that. They are great if you're not in a hurry. I had checked Speedy but prices were...
  23. Replies
    33
    Views
    1,960

    These guys are in Fort Worth: J MOR Machinery...

    These guys are in Fort Worth:

    J MOR Machinery Movers Inc. | Moving Equipment Fort Worth TX
  24. Replies
    30
    Views
    13,719

    Poll: Wow, thanks for the tip. I started with it on...

    Wow, thanks for the tip. I started with it on Monday and I also think it's great. It's almost clear. I don't get eye irritation like with the BC940 and so far no foaming (my other BC940 gripe).
  25. Replies
    1,263
    Views
    177,768

    I'm thinking that might be relatively new. It...

    I'm thinking that might be relatively new. It didn't seem there was any such provision a few years back when I was reading up on failed ventures on KS. Even if it does apply to GD's project,...
Results 1 to 25 of 701
Page 1 of 29 1 2 3 4