Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: sagespecialized

Page 1 of 19 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Fadec?

    by sagespecialized
    Replies
    14
    Views
    8,164

    I believe the whole thing went down the toilet...

    I believe the whole thing went down the toilet last I talked to Daves grandson, about 4 months ago. The grandson had 10-12 mills in his shop that were in the assy process and they were working on a...
  2. Jtek (tool mag and RGV system) and Toyoda have...

    Jtek (tool mag and RGV system) and Toyoda have been working together since the 80's putting together these systems, they are both joined at the hip and are both transparent when it comes to...
  3. Who let the cat outa the bag...LOL!!

    Who let the cat outa the bag...LOL!!
  4. 'Toyoda supports Toyota in Japan. Different...

    'Toyoda supports Toyota in Japan. Different companies but under the same umbrella.

    Go FMS, completely expandable to fit your capacity needs. The machines are up to 500 tool capacity in the matrix...
  5. I'm glad you got it working for you but i think...

    I'm glad you got it working for you but i think your still missing the point. If X10. inches is the middle of your stroke and you reach out with your indicator and indicate the B90 and B270 sides of...
  6. If the bore in the pallet is truly round,...

    If the bore in the pallet is truly round, checking with a dial bore gage, not with an indicator in the spindle as he stated then yes.

    His check, using an indicator in the spindle, tells me that...
  7. No Mr. HYPERTUNE, I fully know of dstryr's...

    No Mr. HYPERTUNE, I fully know of dstryr's capability/ knowledge and understanding of his issue and I am fully confident he can adjust accordingly to get his pallet to run on centerline in his...
  8. Edster, ask Okuma to pull the drive tuning...

    Edster, ask Okuma to pull the drive tuning parameters and programs within the machine and verify the details. Japan likes to run there machines nice and conservative in my experience working with...
  9. DMF_Tomb has it right...your grid shift is off. ...

    DMF_Tomb has it right...your grid shift is off.

    If you have your spindle at X0 and you indicate the bore in the pallet at B90 and B270 and there is a variation, then your X grid needs to be...
  10. You say "when you came in this morning your...

    You say "when you came in this morning your spindle was almost on the table."

    If you have the gas style counter balance maybe it needs to be recharged? The lack of pressure will allow the Z to...
  11. Jump on the Siemans website. There is a...

    Jump on the Siemans website. There is a downloadable file that is used for training purposes and it has a manual in there to run you thru the features.
  12. Replies
    5,132
    Views
    761,041

    Oh I love the boys in purple! Solid guys. I...

    Oh I love the boys in purple! Solid guys.

    I had my Haas stored in there warehouse for 2 years before I moved it out west here. These guys work like a well oiled machine and moved all of the...
  13. Replies
    7
    Views
    3,646

    I would build a sub plate to house the female...

    I would build a sub plate to house the female receivers, then t-nut that to the OE table. You should have no issues if you dust cut the face of the subplate after it has been t-nutted to the table.
    ...
  14. Replies
    23
    Views
    3,692

    ISO or AS regardless of which your dealing with...

    ISO or AS regardless of which your dealing with has to have a buy in from the top brass in order for the said quality system to be effective. It is also one of the requirements of having a quality...
  15. you could still be fighting a short in the x axis...

    you could still be fighting a short in the x axis cable...

    Remember when we jiggled x cable at the horseshoe and it went into alarm state.

    Also, look for that tab under the table I told you...
  16. Hey Haastec, no worries on the political...

    Hey Haastec, no worries on the political correctness. A spade is a spade and you have more years at this then I possibly could. We are just working thru the process of elimination. I see where you...
  17. oh mr. riseandgrind were up early... how did...

    oh mr. riseandgrind were up early...

    how did the slipper clutch R&R work out?
  18. I have been helping riseandgrind work thru the...

    I have been helping riseandgrind work thru the issues. Someone has replaced the shuttle switches with the style that goes on the X and Y axis and they have also done away with the stock adjusting...
  19. currently knocking on wood...but I'll take the...

    currently knocking on wood...but I'll take the Blue Moon regardless..LOL!!

    I had a few of those back in my Toyoda days...

    16 6x6 blocks on one tombstone, 4 tombstones occupied. 1 tombstone ran...
  20. Replies
    7
    Views
    1,398

    I got $.35 here just last week for 6061 alum...

    I got $.35 here just last week for 6061 alum chips. Was $.45 3 weeks ago and was at $.50 4 months ago.

    The issue I have is the purchasing price is going the other way...a guy can't catch a break...
  21. Replies
    20
    Views
    4,335

    I'm with you on this one BobW. Quality is Quality...

    I'm with you on this one BobW. Quality is Quality and you use the appropriate tools to get the job done right.

    Why would one treat a 2A thread quality any different then a 3A thread quality. Parts...
  22. Replies
    20
    Views
    4,335

    I still don't see it... A 2A thread is...

    I still don't see it...

    A 2A thread is external, threading insert (turning) adjusted with comp. Thread mill (milling) adjusted with comp...

    If it was 2B or 3B, internal, that is driven by tap...
  23. Replies
    20
    Views
    4,335

    So you want to charge more to add or subtract...

    So you want to charge more to add or subtract cutter comp....interesting...
  24. Replies
    10
    Views
    2,854

    You have to pull the front Y axis way cover to...

    You have to pull the front Y axis way cover to access the x axis cable where it makes the bend. This will be the location where it is broken. Your local HFO can get you a cable, they run about $275....
  25. Replies
    10
    Views
    2,854

    The 175 alarm turns the servos off, which is why...

    The 175 alarm turns the servos off, which is why you can't move anything.

    Address this issue first and put it to bed. It will make it easier to work out the other issues.
Results 1 to 25 of 470
Page 1 of 19 1 2 3 4